Home › SECURITIES › ENGINE IMMOBILISER › TRANSPONDER KEY ECU

TRANSPONDER KEY ECU > INSTALLATION

for Preparation Click here



1. INSTALL REINFORCEMENT ASSEMBLY (w/ Bracket)
  1. Insert the reinforcement hook into the holes of the bracket, and temporarily install the reinforcement.

  1. Install the instrument panel reinforcement with the 7 bolts.



  1. Install the 2 caps.


    B187910



    I045004E02
  1. Install the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.



  1. Engage the 20 clamps.


    B186407E01

  1. Connect the connector.

  1. Connect the 2 airbag connectors (Click here).



  1. Install the 3 bolts.


    B186406



  1. Engage the 2 clamps and connect the 6 connectors to the air conditioning unit assembly.


    I045003E01



2. INSTALL TRANSPONDER KEY ECU


    B178130
  1. Install the transponder key ECU with the nut.

  1. Connect the connector.



3. INSTALL TRANSPONDER KEY BRACKET (w/ Bracket)
  1. Clean the 3 screw holes.



    B182491
  1. Install the transponder key bracket with 3 new screws.



4. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Bracket)


    I045015E01
  1. Install the air conditioner amplifier assembly with the nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



5. INSTALL DRIVER SIDE JUNCTION BLOCK (w/ Bracket)


    E076135E01
  1. Install the driver side junction block assembly with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL ECM (for 2TR-FE w/ Bracket)

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL ECM (for 1GR-FE w/ Bracket)


    A191699
  1. Install the ECM with the nut and 2 bolts

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A191698
  1. Connect the 6 No. 2 junction block connectors, 6 ECM connectors and wire harness clamp.



8. INSTALL PARKING BRAKE CONTROL LEVER ASSEMBLY (for Manual Transmission w/ Bracket)


F050702E01
  1. Install the parking brake lever assembly with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the sleeve with the pin and clip.



9. INSTALL STEERING COLUMN ASSEMBLY (w/ Bracket)


F051320E01
  1. Install the steering column assembly with the 2 nuts and bolt.

    Torque:
    21 N*m{ 210 kgf*cm , 16 ft.*lbf }

  1. Connect each of the connectors to the steering column assembly.

  1. Connect the wire harness clamps to the steering column assembly.

    CAUTION:
    Use a shop rag to wipe any dirt off the installation plane and column body side.

    NOTICE:
    Be careful not to scratch or soil the installation plane of the steering column.



10. INSTALL STEERING SLIDING YOKE (w/ Bracket)
  1. Align the matchmarks on the steering column and steering sliding yoke.

  1. Install the steering sliding yoke onto the steering column assembly and slide it upward.

  1. Align the matchmarks on the intermediate shaft sub-assembly No. 2 and steering sliding yoke.

  1. Install the sliding yoke onto the intermediate shaft sub- assembly No. 2 with bolts A and B.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for bolt A, B



11. INSTALL STEERING COLUMN HOLE COVER (w/ Bracket)


F051329
  1. Install the steering column hole cover with the 4 clips.



12. INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET (w/ Bracket)


    I045017E01
  1. Install the instrument panel brace mounting bracket RH with the bolt and nut.



    I045016E01
  1. Install the instrument panel brace mounting bracket LH with the bolt and nut.



13. INSTALL AIR DUCT ASSEMBLY RH (w/ Bracket)


    I045023E01
  1. Engage the 3 claws and install the air duct assembly.



14. INSTALL AIR DUCT ASSEMBLY LH (w/ Bracket)


    I045022E01
  1. Engage the 4 claws and install the air duct assembly heater.

  1. Engage the clip.



15. INSTALL NO. 1 REAR AIR DUCT (for Double Cab w/ Bracket)


    I045020E01
  1. Engage the 2 claws and install the air duct rear.

  1. Put the floor carpet back down.



16. INSTALL NO. 2 REAR AIR DUCT (for Double Cab w/ Bracket)


    I045021E01
  1. Engage the 2 claws and install the air duct rear.

  1. Put the floor carpet back down.



17. INSTALL NO. 3 HEATER TO REGISTER DUCT (w/ Bracket)


    I045019E01
  1. Install the heater to register duct with the nut.



18. INSTALL NO. 1 HEATER TO REGISTER DUCT


    I045018E01
  1. Install the heater to register duct with the nut.



19. INSTALL INSTRUMENT PANEL SAFETY PAD
  1. Install the instrument panel safety pad (Click here).