Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. Stereo component amplifier assembly

WIRING DIAGRAM


E233346E01


INSPECTION PROCEDURE

NOTICE:
After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKER)
  1. Disconnect the S24 and S31 stereo component amplifier assembly connectors.

  1. Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Disconnect the S17 and S18 rear speaker assembly connectors.

  1. Disconnect the S21 No. 1 speaker assembly with box connector.

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S24-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    S24-1 (FL-) - Body ground
    Always
    10 kΩ or higher
    S24-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    S24-3 (FR-) - Body ground
    Always
    10 kΩ or higher
    S31-8 (TWL+) - Body ground
    Always
    10 kΩ or higher
    S31-7 (TWL-) - Body ground
    Always
    10 kΩ or higher
    S31-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    S31-6 (TWR-) - Body ground
    Always
    10 kΩ or higher
    S31-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    S31-9 (RL-) - Body ground
    Always
    10 kΩ or higher
    S31-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    S31-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    S24-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    S24-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    S24-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    S24-10 (WFR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E232748E02
  1. Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.4 to 2.2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E233347E01
  1. Disconnect the S19 and S20 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (+) - 3 (-)
    Always
    1.5 to 2.5 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT REAR SPEAKER ASSEMBLY


    E232748E02
  1. Disconnect the S17 and S18 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT NO. 1 SPEAKER ASSEMBLY WITH BOX


    E233348E01
  1. Disconnect the S21 No. 1 speaker assembly with connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (WF+) - 3 (WF-)
    Always
    1.6 to 2.4 Ω
    2 (WF+) - 4 (WF-)
    Always
    1.6 to 2.4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Speaker Assembly with Box)



NG
REPLACE NO. 1 SPEAKER ASSEMBLY WITH BOX (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)