VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING TECHSTREAM) |
Place the vehicle on a level surface with an inclination of less than +/-1°.
Turn the ignition switch OFF.
Check that the steering wheel is in the centered position.
Check that the shift lever is in parking or neutral and apply the parking brake.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Switch the skid control ECU to test mode using the Techstream.
Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.
![]() |
Check that the ABS warning light and VSC OFF indicator light blink as shown in the illustration.
Start the engine.
| TEST MODE (SIGNAL CHECK) PROCEDURE (WHEN USING SST CHECK WIRE) |
Place the vehicle on a level surface with an inclination of less than +/-1°.
Turn the ignition switch off.
Check that the steering wheel is in the centered position.
Check that the shift lever is in parking or neutral and apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
![]() |
Check that the ABS warning light and VSC OFF indicator light blink as shown in the illustration.
Start the engine.
| MASTER CYLINDER PRESSURE SENSOR CHECK |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the skid control buzzer beeps for 1 second.
| YAW RATE SENSOR CHECK |
![]() |
Release the parking brake and drive the vehicle at a speed of 3 km/h (2 mph) or more, and turn the steering wheel either to the left or right 90° or more to turn the vehicle 180°.
Stop the vehicle and move the shift lever to N or P.
Check that the skid control buzzer sounds for 3 seconds.
| DECELERATION SENSOR CHECK |
Release the parking brake and drive the vehicle at a speed of 3 km/h (2 mph) or more, and turn the steering wheel either to the left or right 90° or more to turn the vehicle 180°.
Check that the skid control buzzer sounds for 3 seconds while the vehicle is turning.
| Vehicle Speed km/h (mph) | Turning Radius m (ft.) |
| 10 (6) | 7.87 (25.82) |
| 15 (9) | 17.72 (58.13) |
| 20 (12) | 31.49 (103.31) |
| 25 (16) | 49.21 (161.45) |
| SPEED SENSOR CHECK |
![]() |
Check that the ABS warning light is blinking as shown in the illustration.
Check the reverse signal.
Drive the vehicle in reverse for more than 1 second at 3 km/h (2 mph) or more.
Check the forward signal.

Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ SIGNAL CHECK FUNCTION DTCs (WHEN USING TECHSTREAM) |
Read the DTC(s) by following the instructions on the Techstream screen.
| READ SENSOR SIGNAL CHECK FUNCTION DTCs (WHEN USING SST CHECK WIRE) |
![]() |
Using SST, connect terminals 4 (CG), 12 (TS) and 13 (TC) of the DLC3.
Turn the ignition switch to ON.
Read the number of blinks of the ABS warning light.
![]() |
After the check, disconnect SST from terminals 4 (CG), 12 (TS) and 13 (TC) of the DLC3.
Turn the ignition switch off.
| SENSOR SIGNAL CHECK FUNCTION DTCs |
| DTC Code | Diagnosis | Trouble Areas |
| C1271/71 | Low output signal of front speed sensor RH |
|
| C1272/72 | Low output signal of front speed sensor LH |
|
| C1273/73 | Low output signal of rear speed sensor RH |
|
| C1274/74 | Low output signal of rear speed sensor LH |
|
| C1275/75 | Abnormal change in output signal of front speed sensor RH |
|
| C1276/76 | Abnormal change in output signal of front speed sensor LH |
|
| C1277/77 | Abnormal change in output signal of rear speed sensor RH |
|
| C1278/78 | Abnormal change in output signal of rear speed sensor LH |
|
| C1279/79 | Deceleration sensor output voltage malfunction |
|
| C1281/81 | Master cylinder pressure sensor output malfunction | Master cylinder pressure sensor |
| DTC No. | Diagnosis | Trouble Areas |
| C0371/71 | Yaw rate sensor | Yaw rate sensor |
![]() |