Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A107881E94

Measure the voltage according to the value(s) in the table below.

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column.
The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols)
Wiring Colors
Terminal Descriptions
Conditions
Specified Condition
A24-1 (BATT) - D74-81 (E1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
D74-41 (+BM) - D74-81 (E1)
P - BR
Power source of throttle motor
Always
11 to 14 V
A24-28 (IGSW) - D74-81 (E1)
LG - BR
Ignition switch
Ignition switch ON
11 to 14 V
A24-3 (+B) - D74-81 (E1)
GR - BR
Power source of ECM
Ignition switch ON
11 to 14 V
A24-2 (+B2) - D74-81 (E1)
GR - BR
Power source of ECM
Ignition switch ON
11 to 14 V
D74-58 (OC1+) - D74-57 (OC1-)
L-B - R-B
Camshaft timing oil control valve (OCV for bank 1)
Ignition switch ON
Pulse generation
(See waveform 1)
D74-52 (OC2+) - D74-51 (OC2-)
B - B-L
Camshaft timing oil control valve (OCV for bank 2)
Ignition switch ON
Pulse generation
(See waveform 1)
A24-34 (MREL) - D74-81 (E1)
W - BR
EFI relay
Ignition switch ON
11 to 14 V
D74-67 (VCV1) - D74-97 (ETHW)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D74-66 (VCV2) - D74-98 (ETHA)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D74-74 (VG) - D74-75 (E2G)
L-Y - G-W
Mass air flow meter
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
D74-73 (THA) - D74-98 (ETHA)
Y-B - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
D74-76 (THW) - D74-97 (ETHW)
G-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
D74-80 (VCTA) - D74-79 (ETA)
L - B
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D74-78 (VTA1) - D74-79 (ETA)
R-Y - B
Throttle position sensor (for engine control)
Ignition switch ON, Throttle valve fully closed
0.5 to 1.2 V
Ignition switch ON, Throttle valve fully open
3.2 to 4.8 V
D74-77 (VTA2) - D74-79 (ETA)
Y-B - B
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON, Throttle valve fully open
4.5 to 5.0 V
A24-55 (VPA) - A24-58 (EPA)
W - BE
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
A24-56 (VPA2) - A24-60 (EPA2)
LG - BR
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
A24-57 (VCPA) - A24-58 (EPA)
B - BE
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
A24-59 (VCP2) - A24-60 (EPA2)
V - BR
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
D74-22 (HA1A) - D74-23 (E04)
D74-20 (HA2A) - D74-21 (E05)
L - W-B
G - W-B
A/F sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
D74-126 (A1A+) - D74-81 (E1)
G - BR
A/F sensor
Ignition switch ON
3.3 V*
D74-103 (A2A+) - D74-81 (E1)
V - BR
A/F sensor
Ignition switch ON
3.3 V*
D74-125 (A1A-) - D74-81 (E1)
R - BR
A/F sensor
Ignition switch ON
2.9 V*
D74-102 (A2A-) - D74-81 (E1)
P - BR
A/F sensor
Ignition switch ON
2.9 V*
D74-45 (HT1B) - D74-81 (E1)
D74-44 (HT2B) - D74-81 (E1)
G - BR
B - BR
Heated oxygen sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
D74-114 (OX1B) - D74-115 (EX1B)
D74-112 (OX2B) - D74-113 (EX2B)
W - BR
B - BR
Heated oxygen sensor
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 2)
D74-86 (#10) - D74-43 (E01)
D74-109 (#20) - D74-43 (E01)
D74-85 (#30) - D74-43 (E01)
D74-108 (#40) - D74-43 (E01)
D74-84 (#50) - D74-43 (E01)
D74-107 (#60) - D74-43 (E01)
R-L - W-B
L - W-B
R - W-B
Y - W-B
G - W-B
R - W-B
Injector
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 3)
D74-94 (KNK1) - D74-93 (EKNK)
G - R
Knock sensor (bank 1)
Engine speed maintained at 4000 rpm after warming up
Pulse generation
(See waveform 4)
D74-117 (KNK2) - D74-116 (EKN2)
W - B
Knock sensor (bank 2)
Engine speed maintained at 4000 rpm after warming up
Pulse generation
(See waveform 4)
D74-90 (VV1+) - D74-89 (VV1-)
R - L-R
Variable valve timing (VVT) sensor (bank 1)
Idling
Pulse generation
(See waveform 5)
D74-87 (VV2+) - D74-88 (VV2-)
R - G
Variable valve timing (VVT) sensor (bank 2)
Idling
Pulse generation
(See waveform 5)
D74-110 (NE+) - D74-111 (NE-)
B - W
Crankshaft position sensor
Idling
Pulse generation
(See waveform 5)
D74-40 (IGT1) - D74-81 (E1)
D74-39 (IGT2) - D74-81 (E1)
D74-38 (IGT3) - D74-81 (E1)
D74-37 (IGT4) - D74-81 (E1)
D74-36 (IGT5) - D74-81 (E1)
D74-35 (IGT6) - D74-81 (E1)
B-R - BR
L-Y - BR
B - BR
L-B - BR
G-R - BR
G - BR
Ignition coil
(ignition signal)
Idling
Pulse generation
(See waveform 6)
D74-104 (IGF1) - D74-81 (E1)
G-B - BR
Ignition coil
(ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 6)
D74-63 (PRG) - D74-81 (E1)
L-B - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 7)
A24-13 (SPD) - D74-81 (E1)
B - BR
Speed signal from combination meter
Ignition switch ON, Driving wheel rotated slowly
Pulse generation
(See waveform 8)
A24-46 (STA) - D74-81 (E1)
R - BR
Starter signal
Cranking
6.0 V or more
A24-36 (STP) - D74-81 (E1)
LG - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A24-35 (ST1-) - D74-81 (E1)
R - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
D74-120 (NSW) - D74-81 (E1)
L - BR
Park/Neutral position switch
Ignition switch ON, Shift lever position in P or N
Below 3.0 V
Ignition switch ON, Shift lever position other than P and N
11 to 14 V
D74-19 (M+) - D74-82 (ME01)
R - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 9)
D74-18 (M-) - D74-82 (ME01)
G - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 10)
A24-48 (FC) - D74-81 (E1)
L - BR
Fuel pump control
Ignition switch ON
11 to 14 V
A24-24 (W) - D74-81 (E1)
P - BR
MIL
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
A24-16 (TC) - D74-81 (E1)
R - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
A24-15 (TACH) - D74-81 (E1)
W - BR
Engine speed
Idling
Pulse generation
(See waveform 11)
D74-62 (ACIS) - D74-81 (E1)
R-W - BR
VSV for ACIS
Ignition switch ON
11 to 14 V
D74-72 (PSW) - D74-81 (E1)
L - BR
P/S pressure switch
Ignition switch ON
11 to 14 V
A24-30 (VPMP) - D74-81 (E1)
V - BR
Vent valve
(built into canister pump module)
Ignition switch ON
11 to 14 V
A24-49 (MPMP) - D74-81 (E1)
G - BR
Leak detection pump
(built into canister pump module)
Leak detection pump OFF
0 to 3 V
Leak detection pump ON
11 to 14 V
D74-121 (PPMP) - D74-97 (ETHW)
P - BR
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3 to 3.6 V
D74-28 (AIRV) - D74-81 (E1)
BR - BR
Air switching valve (bank 1) for secondary air injection system
Idling
11 to 14 V
A24-43 (ARV2) - D74-81 (E1)
V - BR
Air switching valve (bank 2) for secondary air injection system
Idling
11 to 14 V
D74-54 (AIRP) - D74-81 (E1)
P - BR
Air pump (bank 1) control
Idling
11 to 14 V
D74-53 (ARP2) - D74-81 (E1)
P-L - BR
Air pump (bank 2) control
Idling
11 to 14 V
D74-30 (AIDI) - D74-81 (E1)
G - BR
Diagnostic information signal for air injection system
Air injection system operates
Pulse generation
(See waveform 14)
D74-29 (AID2) - D74-81 (E1)
G - BR
Diagnostic information signal for air injection system
Air injection system operates
Pulse generation
(See waveform 14)
A24-54 (AIP) - D74-98 (ETHA)
Y - BR
Secondary air injection system pressure signal
Ignition switch ON
4.5 to 5.0 V
A24-53 (AIP2) - D74-98 (ETHA)
G - BR
Secondary air injection system pressure signal
Ignition switch ON
4.5 to 5.0 V
A24-10 (CANH) - D74-81 (E1)
GR - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 12)
A24-11 (CANL) - D74-81 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 13)
A24-52 (FPC) - D74-81 (E1)
BE - BR
Fuel pump control
Ignition switch ON
11 to 14 V
A24-18 (DI) - D74-81 (E1)
L - BR
Fuel pump control
Ignition switch ON
0 to 3.0 V
A24-14 (STSW) - D74-81 (E1)
BR - BR
Ignition switch signal
Shift lever position P or N, ignition switch START
6.0 V or more
A24-41 (ACCR) - D74-81 (E1)
BR - BR
ACC (Accessory) relay control signal
Cranking
Below 1.5 V
D74-16 (STAR) - D74-81 (E1)
L - BR
Starter relay control
Ignition switch ON
Below 1.5 V
Cranking
6.0 V or more
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E07
Camshaft timing oil control valve (OCV) 
ECM Terminal Name
Between OC1+ and OC1- or OC2+ and OC2-
Tester Range
5 V/DIV., 1 msec./DIV.,
Condition
Idling

WAVEFORM 2
A088863E02
Heated oxygen sensor 
ECM Terminal Name
Between OX1B and E2 or OX2B and E2
Tester Range
0.2 V/DIV., 200 msec./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 3
G035622E03
Fuel injector 
ECM Terminal Name
Between #10 (to 60) and E01
Tester Range
30 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 4
A085286E65
Knock sensor 
ECM Terminal Name
Between KNK1 and EKNK or KNK2 and EKN2
Tester Range
1 V/DIV., 0.01 to 1 msec./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine rpm increases.
  2. The waveforms and amplitudes displayed on the Techstream differ slightly depending on the vehicle.


WAVEFORM 5
G035795E28
  1. Crankshaft position sensor

  2. VVT sensor
    ECM Terminal Name
    (a) Between NE+ and NE-
    (b) Between VV1+ and VV1- or VV2+ and VV2-
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 6
G035664E03
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)
    ECM Terminal Name
    (a) Between IGT (1 to 6) and E1
    (b) Between IGF1 and E1
    Tester Ranges
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 7
A164291E01
Purge VSV 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV., 10 to 100 msec./DIV.
Condition
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 8
A093224E02
Vehicle speed signal 
ECM Terminal Name
Between SPD and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Ignition switch ON, Rotate driving wheel slowly

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 9
A093275E02
Throttle actuator positive terminal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 10
A093274E02
Throttle actuator negative terminal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A093225E03
Engine speed signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 12
A086154E14
CAN communication signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Ignition switch ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 13
A086155E15
CAN communication signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Ignition switch ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 14
G037721E05
Terminal AID of air injection control driver 
ECM Terminal Name
Between AIDI and E1 or AID2 and E1
Tester Range
5 V/DIV., 100 msec./DIV.
Condition
Performing Active Test using Techstream (air injection system)

HINT:
The wavelength changes when the air injection control driver detects malfunctions in the air injection system .