Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

NOTICE:
In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the Techstream ON.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.


Tester Display
Measurement Item/Range
Normal Condition*3
Diagnostic Note
Vehicle Speed
Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed:
Min.: 0 rpm, Max.: 16383.75 rpm
650 to 750 rpm: Idling
-
Calculate Load
Calculated load by ECM:
Min.: 0%, Max.: 100%
  1. 11.4 to 16.4%: Idling
  1. 13.1 to 18.9%: Running without load (2000 rpm)
-
Vehicle Load
Vehicle load:
Min.: 0%, Max.: 25700%
Actual vehicle load
Load percentage in terms of maximum intake air flow amount
MAF
Air flow rate from MAF meter:
Min.: 0 g/sec., Max.: 655.35 g/sec.
3.2 to 4.7 g/sec.: Idling
13.1 to 18.9 g/sec.: 2000 rpm
If value approximately 0.0 g/sec.:
  1. Mass air flow meter power source circuit open
  1. VG circuit open or short
If value 160.0 g/sec. or more:
  1. E2G circuit open
Atmospheric Pressure
Atmospheric pressure:
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure)
-
Coolant Temp
Engine coolant temperature:
Min.: -40°C, Max.: 140°C
80 to 100°C (176 to 212°F):
After warming up
  1. If value -40°C (-40°F): sensor circuit open
  1. If value 140°C (284°F): sensor circuit shorted
Intake Air
Intake air temperature:
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature
  1. If value -40°C (-40°F): sensor circuit open
  1. If value 140°C (284°F): sensor circuit shorted
Engine Run Time
Engine run time:
Min.: 0 s,
Max.: 65535 s
Time after engine start
-
Initial Engine Coolant Temp
Initial engine coolant temperature:
Min.: -40°C, Max.: 120°C
Coolant temperature when engine started
Service data
Initial Intake Air Temp
Initial intake air temperature:
Min.: -40°C, Max.: 120°C
Intake air temperature when engine started
Service data
Battery Voltage
Battery voltage:
Min.: 0, Max.: 65.535 V
11 to 14 V: Idling
-
Accel Sens. No.1 Volt %
Accelerator Pedal Position (APP) No. 1:
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal released
54 to 86%: Accelerator pedal fully depressed
-
Accel Sens. No.2 Volt %
APP No. 2:
Min.: 0%, Max.: 100%
12 to 42%: Accelerator pedal released
66 to 98%: Accelerator pedal fully depressed
-
Accel Sensor Out No.1
APP sensor No. 1 voltage:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No.2
APP sensor No. 2 voltage:
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: Accelerator pedal released
3.4 to 5.0 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle:
ON or OFF
ON: Idling
-
Accel Fully Close #1 (AD)
Accelerator fully closed value No. 1 (AD):
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Accel Fully Close Learn #1
Accelerator fully closed learning value No. 1:
Min.: 0 deg., Max.: 124.512 deg.
-
ETCS service data
Accel Fully Close Learn #2
Accelerator fully closed learning value No. 2:
Min.: 0 deg., Max.: 124.512 deg.
-
ETCS service data
Throttle Sensor Volt %
Throttle sensor positioning:
Min.: 0%, Max.: 100%
0 to 10%: Idling
Calculated value based on VTA1
Throttl Sensor #2 Volt %
Absolute throttle sensor positioning #2:
Min.: 0%, Max.: 100%
-
Calculated value based on VTA2
ST1
Brake pedal signal:
ON or OFF
ON: Brake pedal released
-
System Guard
System guard:
ON or OFF
-
-
Open Side Malfunction
Open side malfunction:
ON or OFF
-
-
Throttle Idle Position
Whether or not throttle position sensor detecting idle:
ON or OFF
ON: Idling
-
Throttle Require Position
Throttle requirement position:
Min.: 0 V, Max.: 5 V
0.5 to 1.0 V: Idling
-
Throttle Sensor Position
Throttle sensor positioning:
Min.: 0%, Max.: 100%
10 to 18%: Idling
Calculated value based on VTA1
Throttle Position No.1
Throttle position No. 1:
Min.: 0 V, Max.: 5 V
  1. 0.7 to 1.3 V: Throttle fully closed
  1. 3.3 to 4.9 V: Throttle fully open
-
Throttle Position No.2
Throttle position No. 2:
Min.: 0 V, Max.: 5 V
  1. 2.5 to 3.4 V: Throttle fully closed
  1. 4.6 to 5.0 V: Throttle fully open
-
Throttle Position Command
Throttle position command value:
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V
ETCS service data
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.9804 V
0.6 to 1.0 V
ETCS service data
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.9804 V
2.0 to 2.6 V
ETCS service data
Throttle Sens Open #1 (AD)
Throttle sensor opener position No. 1 (AD):
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 V
ETCS service data
Throttle Motor
Whether or not throttle actuator control permitted:
ON or OFF
ON: Idling
-
Throttle Motor Current
Throttle actuator current:
Min.: 0 A, Max.: 19.92 A
0 to 3.0 A: Idling
-
Throttle Motor DUTY
Throttle actuator duty:
Min.: 0%, Max.: 100%
0.5 to 40%: Idling
-
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open):
Min.: 0%, Max.: 100%
-
-
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close):
Min.: 0%, Max.: 100%
-
-
Throttle Fully Closed Learn
Throttle valve fully closed
(learned value):
Min.: 0 V, Max.: 5 V
0.4 to 0.8 V
-
ETCS Actuator Power
Whether or not electric throttle control system power inputted:
ON or OFF
ON: Idling
-
+BM Voltage
+BM voltage:
Min.: 0, Max.: 19.922
10 to 15: Idling
-
Actuator Power Supply
Actuator power supply:
ON or OFF
ON: Idling
-
Fail Safe Drive
Whether or not fail safe function executed:
ON or OFF
ON: ETCS has failed
-
Fail Safe Drive (Main CPU)
Whether or not fail safe function executed:
ON or OFF
ON: ETCS has failed
-
Injector (Port)
Injection period of the No. 1 cylinder:
Min.: 0 ms, Max.: 32.64 ms
1.6 to 2.4 msec.: Idling
-
Injection Volum (Cylinder 1)
Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.048 ml
0.005 to 0.015 ml: Idling
Quantity of fuel injection volume for 10 times (Port and Direct)
Fuel Pump/Speed Status
Fuel pump/status:
ON or OFF
-
Active Test support data
Vacuum Pump
Key-OFF EVAP system leak detection pump status:
ON or OFF
-
Active Test support data
EVAP (Purge) VSV
EVAP (Purge) VSV control duty:
Min.: 0%, Max.: 100%
0 to 100%: Idling
Order signal from ECM
Evap Purge Flow
Purge flow:
Min.: 0%, Max.: 102.4%
0 to 100%: Idling
Service data
Purge Destiny Learn Value
Learning value of purge density:
Min.: -50, Max.: 350
-35 to 1: Idling
Service data
Vapor Pressure Pump
Vapor pressure:
Min.: 33.853 kPa,
Max.: 125.596 kPa
Approximately 100 kPa:
Ignition switch ON
EVAP system pressure monitored by canister pressure sensor
Vapor Pressure (calculated)
Vapor pressure (calculated):
Min.: -5.632 kPa,
Max.: 7153264 kPa
Approximately 100 kPa:
Ignition switch ON
EVAP system pressure monitored by canister pressure sensor
EVAP System Vent Value
key-OFF EVAP system vent valve status:
ON or OFF
-
Active Test support data
EVAP Purge VSV
VSV status for EVAP control:
ON or OFF
-
Active Test support data
Target Air-Fuel Ratio
Air-fuel ratio:
Min.: 0, Max.: 1.999
0.8 to 1.2: Idling
-
AF Lambda B1S1
Short-term fuel trim associated with bank 1 sensor 1:
Min.: 0, Max.: 1.999
  1. Value less than 1 (0.000 to 0.999) = Rich
  1. Stoichiometric air-fuel ratio = 1
  1. Value greater than 1 (1.001 to 1.999) = Lean
-
AF Lambda B2S1
Short-term fuel trim associated with bank 2 sensor 1:
Min.: 0, Max.: 1.999
  1. Value less than 1 (0.000 to 0.999) = Rich
  1. Stoichiometric air-fuel ratio = 1
  1. Value greater than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
A/F sensor output voltage bank 1 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AFS Voltage B2S1
A/F sensor output voltage bank 2 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B1S1
A/F sensor output current bank 1 sensor 1:
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B2S1
A/F sensor output current bank 2 sensor 1:
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
O2S B1S2
Heated oxygen sensor output voltage bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 44 mph (70 km/h)
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
O2S B2S2
Heated oxygen sensor output voltage bank 2 sensor 2:
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 44 mph (70 km/h)
Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
O2S Impedance B1S2
Sub heated oxygen sensor impedance (bank 1 sensor 2):
Min.: 0 Ω, Max.: 21247.68 Ω
5 to 15000:
After driving approx. 10 min. in urban area
-
O2S Impedance B2S2
Sub heated oxygen sensor impedance (bank 2 sensor 2):
Min.: 0 Ω, Max.: 21247.68 Ω
5 to 15000:
After driving approx. 10 min. in urban area
-
Short FT #1
Short-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-30 to 30%
Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim of bank 1
Average value for fuel trim system of bank 1:
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling
-
Short FT #2
Short-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2
Long-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
-30 to 30%
Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
Total FT #2
Total fuel trim of bank 1
Average value for fuel trim system of bank 2:
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling
-
Fuel System Status #1
Fuel system status (bank 1):
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
Fuel System Status #2
Fuel system status (bank 2):
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
Air pump pressure (absolute)
Air pump pressure (absolute):
Min.: 0 kPa, Max.: 320 kPa
Atmospheric pressure +2.5 kPa or more: Air pump ON, Air switching valve open
Close to atmospheric pressure: Air pump OFF, Air switching valve close
(Click here)
Air Pump2 Pressure (Absolute)
Air pump 2 pressure (absolute):
Min.: 0 kPa, Max.: 320 kPa
Atmospheric pressure +2.5 kPa or more: Air pump2 ON, Air switching valve open
Close to atmospheric pressure: Air pump2 OFF, Air switching valve close
(Click here)
Air Pump Pulsation Pressure
Air pump pulsation pressure:
Min.: 0 kPa, Max.: 639.9 kPa
-
Cumulative pulsation pressure calculated by ECM
(Click here)
Air Pump2 Pulsation Pressure
Air pump 2 pulsation pressure:
Min.: 0 kPa, Max.: 639.9 kPa
-
Cumulative pulsation pressure calculated by ECM
(Click here)
Secondary Air Control VSV
VSV status for secondary air control:
ON or OFF
-
Active Test support data
2nd Air System Status
Secondary air injection system status:
ON or OFF
ON: Secondary air system operation
-
AI Test
Secondary air injection system operation prohibition:
OK or NG
-
(Click here)
IGN Advance
Ignition timing advance for No. 1 cylinder:
Min.: -64 deg., Max.: 63.5 deg.
BTDC 7 to 24°: Idling
-
Knock Feedback Value
Feedback value of knocking:
Min: -64°CA, Max.: 1984°CA
-22 to 0°CA:
Driving at 44 mph (70 km/h)
Service data
Knock Correct Learn Value
Correction learning value of knocking:
Min: -64°CA, Max.: 1984°CA
0 to 22°CA:
Driving at 44 mph (70 km/h)
Service data
ACIS VSV
VSV status for ACIS control:
ON or OFF
-
Active Test support data
VVT Control Status #1
VVT control (bank 1) status:
ON or OFF
-
Active Test support data
VVT Control Status #2
VVT control (bank 2) status:
ON or OFF
-
Active Test support data
VVT Aim Angle #1*4
VVT aim angle (bank 1):
Min.: 0%, Max.: 100%
0 to 100%: Idling
VVT duty signal value during intrusive operation
VVT Change Angle #1*4
VVT change angle (bank 1):
Min.: 0°FR, Max.: 60°FR
0 to 56°FR: Idling
Displacement angle during intrusive operation
VVT OCV Duty #1*4
VVT OCV operation duty (bank 1):
Min.: 0%, Max.: 100%
0 to 100%: Idling
Requested duty value for intrusive operation
VVT Aim Angle #2*4
VVT aim angle (bank 2):
Min.: 0%, Max.: 100%
0 to 100%: Idling
VVT duty signal value during intrusive operation
VVT Change Angle #2*4
VVT change angle (bank 2):
Min.: 0°FR, Max.: 60°FR
0 to 56°FR: Idling
Displacement angle during intrusive operation
VVT OCV Duty #2*4
VVT OCV operation duty (bank 2):
Min.: 0%, Max.: 100%
0 to 100%: Idling
Requested duty value for intrusive operation
Catalyst Temp B1S1
Catalyst temperature (bank 1 sensor 1):
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S1
Catalyst temperature (bank 2 sensor 1):
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B1S2
Catalyst temperature (bank 1 sensor 2):
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S2
Catalyst temperature (bank 2 sensor 2):
Min.: -40°C, Max.: 6513.5°C
-
-
Starter Signal
Starter signal:
ON or OFF
ON: Cranking
-
Starter Control
Starter switch status:
ON or OFF
ON: Cranking
-
Power Steering Signal Record
Power steering switch:
ON or OFF
ON: Power steering operation
-
Starter Relay
Starter relay status:
ON or OFF
ON: Cranking
-
Power Steer. Sig. Record
Power steering signal (history):
ON or OFF
ON: When steering wheel first turned after battery terminals connected
This signal status usually ON until battery terminals disconnected
ACC Relay
ACC relay status:
ON or OFF
ON: Cranking
-
Neutral Position SW Signal
PNP switch status
ON or OFF
ON: P or N position
-
Stop Light Switch
Stop light switch status:
ON or OFF
ON: Brake pedal depressed
-
A/C Signal
A/C switch status:
ON or OFF
ON: A/C ON
-
Closed Throttle Position SW
Closed throttle position switch:
ON or OFF
  1. ON: Throttle fully closed
  1. OFF: Throttle open
-
Fuel Cut Condition
Fuel cut condition:
ON or OFF
ON: Fuel cut operating
-
Electrical Load Signal
Electrical load signal:
ON or OFF
ON: Headlights or defogger turned ON
-
Check Mode
Check mode:
ON or OFF
ON: Check mode ON
(Click here)
SPD Test Result
Check mode result for vehicle speed sensor:
Compl or Incmpl
-
-
AS Test Result
Check mode result for secondary air injection system:
Compl or Incmpl
-
-
Misfire Test Result
Check mode result for misfire monitor:
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for HO2 sensor (bank 1):
Compl or Incmpl
-
-
OXS2 Test Result
Check mode result for HO2 sensor (bank 2):
Compl or Incmpl
-
-
A/F Test Results #2
Check mode result for air-fuel ratio sensor (bank 2):
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air-fuel ratio sensor (bank 1):
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor:
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor:
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor:
Not Avl or Avail
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Not Avl or Avail
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Compl or Incmpl
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) monitor:
Not Avl or Avail
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor:
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor:
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor:
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor:
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor:
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor:
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor:
Compl or Incmpl
-
-
Component Monitor ENA
Comprehensive component monitor:
Unable or Enable
-
-
Component Monitor CMPL
Comprehensive component monitor:
Compl or Incmpl
-
-
Fuel System Monitor ENA
Fuel system monitor:
Unable or Enable
-
-
Fuel System Monitor CMPL
Fuel system monitor:
Compl or Incmpl
-
-
Misfire Monitor ENA
Misfire monitor:
Unable or Enable
-
-
Misfire Monitor CMPL
Misfire monitor:
Compl or Incmpl
-
-
EGR/VVT Monitor ENA
EGR monitor:
Unable or Enable
-
-
EGR/VVT Monitor CMPL
EGR monitor:
Compl or Incmpl
-
-
Heater Monitor ENA
O2S (A/FS) heater monitor:
Unable or Enable
-
-
Heater Monitor CMPL
O2S (A/FS) heater monitor:
Compl or Incmpl
-
-
O2S (A/FS) Monitor ENA
O2S (A/FS) monitor:
Unable or Enable
-
-
O2S (A/FS) Monitor CMPL
O2S (A/FS) monitor:
Compl or Incmpl
-
-
A/C Monitor ENA
A/C monitor:
Unable or Enable
-
-
A/C Monitor CMPL
A/C monitor:
Compl or Incmpl
-
-
2nd Air Monitor ENA
2nd air monitor:
Unable or Enable
-
-
2nd Air Monitor CMPL
2nd air monitor:
Compl or Incmpl
-
-
EVAP Monitor ENA
EVAP monitor:
Unable or Enable
-
-
EVAP Monitor CMPL
EVAP monitor:
Compl or Incmpl
-
-
Heated Cat Monitor ENA
Heated catalyst monitor:
Unable or Enable
-
-
Heated Cat Monitor CMPL
Heated catalyst monitor:
Compl or Incmpl
-
-
Catalyst Monitor ENA
Catalyst monitor:
Unable or Enable
-
-
Catalyst Monitor CMPL
Catalyst monitor:
Compl or Incmpl
-
-
# Codes (Include History)
#Codes:
Min.: 0, Max.: 255
-
Number of detected DTCs
MIL
MIL status:
ON or OFF
ON: MIL ON
-
MIL ON Run Distance
MIL ON run distance:
Min.: 0 km,
Max.: 65535 km
Distance after DTC detected
-
Running Time from MIL ON
Running time from MIL ON:
Min.: 0 min.,
Max.: 65535 min.
Equivalent to running time after MIL ON
-
Time after DTC Cleared
Time after DTC cleared:
Min.: 0 min.,
Max.: 65535 min.
Equivalent to time after DTCs erased
-
Distance from DTC Cleared
Distance after DTC cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs erased
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared:
Min.: 0, Max.: 255
-
Number of warm-up cycles after DTC cleared
OBD Requirements
OBD requirement
OBD2
-
Number of Emission DTC
Emission related DTCs
-
Number of emission related DTCs
TC and TE1
TC and CG (TE1) terminals of DLC3:
ON or OFF
-
Active Test support data
Ignition Trig. Count
Number of counts of misfire counter:
Min.: 0, Max.: 800
0 to 800
-
Cylinder #1 Misfire Count
Misfire count of cylinder 1:
Min.: 0, Max.: 255
0
This item displayed only when idling
Cylinder #2 Misfire Count
Misfire count of cylinder 2:
Min.: 0, Max.: 255
0
This item displayed only when idling
Cylinder #3 Misfire Count
Misfire count of cylinder 3:
Min.: 0, Max.: 255
0
This item displayed only when idling
Cylinder #4 Misfire Count
Misfire count of cylinder 4:
Min.: 0, Max.: 255
0
This item displayed only when idling
Cylinder #5 Misfire Count
Misfire count of cylinder 5:
Min.: 0, Max.: 255
0
This item displayed only when idling
Cylinder #6 Misfire Count
Misfire count of cylinder 6:
Min.: 0, Max.: 255
0
This item displayed only when idling
All Cylinders Misfire Rate
All cylinders misfire count:
Min.: 0, Max.: 255
0 to 35
-
Misfire RPM
Average engine speed during misfire:
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Average load during misfire:
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire margin:
Min.: -100%, Max.: 99.22%
-100 to 99.22%
Misfire detecting margin
Catalyst OT MF F/C
Catalyst over temperature Misfire prevention fuel cut:
Not Avl or Avail
Avail: Cat OT MF F/C available
Not Avl: Cat OT MF F/C not available
-
Cat OT MF F/C History
Catalyst over temperature Misfire prevention fuel cut history:
ON or OFF
ON: Fuel cut operation history exists
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected):
ON or OFF
ON: Fuel cut is operating
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected):
ON or OFF
ON: Fuel cut is operating
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected):
ON or OFF
ON: Fuel cut is operating
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected):
ON or OFF
ON: Fuel cut is operating
-
Cat OT MF F/C Cylinder#5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected):
ON or OFF
ON: Fuel cut is operating
-
Cat OT MF F/C Cylinder#6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected):
ON or OFF
ON: Fuel cut is operating
-
ACT VSV
A/C cut status for Active Test:
ON or OFF
-
Active Test support data
Idle Fuel Cut
Fuel cut idle:
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
FC TAU
Fuel cut TAU (Fuel cut during very light load):
ON or OFF
ON: Fuel cut operating
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Model Code
Model code
-
Identifying model code:
GSK5#
Engine Type
Engine type
-
Identifying engine type:
1GRFE
Cylinder Number
Cylinder number:
Min.: 0, Max.: 255
-
Identifying cylinder number:
6
Transmission Type
Transmission type
-
Identifying transmission type:
5AT
Destination
Destination
-
Identifying destination:
A (America)
Model Year
Model year:
Min.: 1900, Max.: 2155
-
Identifying model year:
200#
System Identification
System identification
-
Identifying engine system:
GASOLINE (gasoline engine)
Engine Speed of Cyl #1
Engine RPM for cylinder 1:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #2
Engine RPM for cylinder 2:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #3
Engine RPM for cylinder 3:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #4
Engine RPM for cylinder 4:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #5
Engine RPM for cylinder 5:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Engine Speed of Cyl #6
Engine RPM for cylinder 6:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using Active Test
Av Engine Speed of All Cyl
Engine RPM for all cylinders:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
-
SPD (NT)
Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
Lock-up is
  1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
  2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
Data is displayed in increments of 50 rpm

HINT:
  1. *3: If no idling conditions are specified, the shift lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.
  2. *4: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank1), Control the VVT Linear (Bank2), Control the VVT Exhaust Linear (Bank1) and Control the VVT Exhaust Linear (Bank2). For other Active Tests, the Data List value will be 0.


ACTIVE TEST

HINT:
Using the Techstream to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the Techstream ON.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. According to the display on Techstream, perform the "Active Test".


Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
-12.5 to 24.8%
  1. All injectors tested at the same time
  1. Perform test at less than 3000 rpm
  1. Injection volume can be changed in 1% graduations within control range
Control the Injection Volume for A/F Sensor
Change injection volume
Lower by 12.5% or increase by 24.8%
  1. Perform test at less than 3000 rpm
  1. Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs
  1. To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F Control System / AFS B1 S1 and O2S B1 S2
Activate the VSV for Secondary Air Control
Activate the Secondary Air System
ON/OFF
  1. Do not perform test for 5 seconds or more
  2. After test, do not perform test again for 30 seconds
Activate the VSV for Intake Control
Activate VSV for intake control
ON/OFF
-
Activate the VSV for EVAP Control
Activate purge VSV control
ON/OFF
-
Control the A/C Cut Signal
Control the A/C cut signal
ON/OFF
-
Control the Fuel Pump Speed
Activate fuel pump (C/OPN Relay)
ON/OFF
Test possible when following conditions met:
  1. Ignition switch ON
  1. Engine is stopped
Connect the TC and TE1
Turn on and off TC and CG (TE1) connection
ON/OFF
  1. ON: TC and TE1 connected
  1. OFF: TC and TE1 disconnected
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
-
Prohibit the Catalyst OT Misfire prevent F/C
Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
ON: Fuel cut is prohibited
Confirm that the Vehicle is Stopped and Engine Speed is 3000 rpm or less.
Active the Starter Relay
Activate starter relay
ON/OFF
-
Active the ACC Cut Relay
Activate ACC cut relay
ON/OFF
Test possible when following conditions met:
  1. Ignition switch ON
  1. Engine is stopped
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
Test possible when following conditions met:
  1. Ignition switch ON
  1. Engine is stopped
  1. Fully depressing accelerator pedal (APP: 58 degrees or more)
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Control the VVT Linear (Bank1)
Control VVT (bank 1)
Between -128 and 127%
  1. Engine stall or rough idle when VVT actuator operated by 100%.
  2. Test possible during idle.
Control the VVT System (Bank1)
Turn on and off OCV
(Oil Control Valve)
ON/OFF
  1. Engine stalls or idles roughly when OCV turned ON
  2. Normal engine running or idling when OCV OFF
Control the VVT Linear (Bank2)
Control VVT (bank 2)
Between -128 and 127%
  1. Engine stall or rough idle when VVT actuator operated by 100%.
  2. Test possible during idle.
Control the VVT System (Bank2)
Turn on and off OCV
(Oil Control Valve)
ON/OFF
  1. Engine stalls or idles roughly when OCV turned ON
  2. Normal engine running or idling when OCV OFF
Activate the Vacuum Pump
Leak detection pump
ON/OFF
-
Activate the VSV for Vent Value
Vent valve
ON/OFF
-
Control the Target Fuel Pressure
Control Fuel Pressure
Between -12.5 and 24.8%
Confirm that the Engine Speed is 3000 rpm or less.
Control the Cylinder #1 Fuel Cut
Cylinder #1 injector fuel cut
ON/OFF
Test possible while vehicle stopped and engine idling*3
Control the Cylinder #2 Fuel Cut
Cylinder #2 injector fuel cut
ON/OFF
Control the Cylinder #3 Fuel Cut
Cylinder #3 injector fuel cut
ON/OFF
Control the Cylinder #4 Fuel Cut
Cylinder #4 injector fuel cut
ON/OFF
Control the Cylinder #5 Fuel Cut
Cylinder #5 injector fuel cut
ON/OFF
Control the Cylinder #6 Fuel Cut
Cylinder #6 injector fuel cut
ON/OFF
Control the All Cylinder Fuel Cut
All cylinder fuel cut
ON/OFF
Check the Cylinder Compression*4
Check the cylinder compression pressure
ON/OFF
Fuel injection and ignition stop in all cylinders

NOTICE:
  1. *3: If the display of the Data List's CAT OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
  2. *3: If the display of the Data List's CAT OT MF F/C item is Avail, perform this Active Test as described below.
    1. Stop the engine and turn the ignition switch ON to turn Control the Cylinder #1 Fuel Cut (to #6 Fuel Cut) ON.
    2. Start the engine.

HINT:
*4: When cranking the engine, each cylinder measures the engine rpm.
In this Active Test, the fuel and ignition of all cylinders are cut, and cranking occurs for approximately 10 seconds. Then, each cylinder measures the engine rpm. If a cylinder's engine rpm is higher than the others, that cylinder's compression pressure is compared to the others, and it is determined whether it is low or not.

  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch ON and turn the Techstream ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4, Engine Speed of Cyl #5, Engine Speed of Cyl #6 and Av Engine Speed of All Cyl.

  6. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

    HINT:
    After performing the above procedure, the Active Test's Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine rpm measurement will enter standby mode.

  7. Crank the engine for about 10 seconds.
  8. Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the Techstream.

    HINT:
    At first, the Techstream's display will show each cylinder's engine rpm measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine rpm measurement will change to the actual engine rpm.

    NOTICE:
    1. After the Active Test's Check the Cylinder Compression is turned ON, it will automatically turn off after 255 seconds.
    2. When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.
    3. If the Check the Cylinder Compression test needs to be performed after it is turned ON and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
    4. Use a fully-charged battery.


SYSTEM CHECK

HINT:
Performing a System Check in the Utility menu enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the Techstream ON.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the table below.


Tester Display
Test Part
Control Range
Diagnostic Note
Evaporative System Check
(Automatic Mode)
Perform 5 steps in order to operate EVAP key-off monitor automatically
35°C (95°F) or less
  1. If no DTCs in Pending after performing this test, system functioning normally
  1. Refer to EVAP system (Click here)
Evaporative System Check
(Manual Mode)
Perform 5 steps in order to operate EVAP key-off monitor manually
35°C (95°F) or less
  1. Used to detect malfunctioning parts
  1. Refer to EVAP system (Click here)
Air Injection Check
(Automatic Mode)
Perform secondary air injection system operation automatically
With warm engine, ignition switch turned OFF once
  1. If no DTCs in Pending after performing this test, system functioning normally
  2. Refer to inspection procedure for secondary air injection system DTCs
  3. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running
  4. Turn ignition switch to OFF when Air Injection Check finished
Air Injection Check
(Manual Mode)
Perform 7 operations in order to operate air injection system monitor manually
With warm engine, ignition switch turned OFF once
  1. Used to detect malfunctioning parts
  2. Refer to inspection procedure for secondary air injection system DTCs
  3. When performing Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running
  4. Turn ignition switch to OFF when Air Injection Check finishes