Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > CHECKING MONITOR STATUS

for Preparation Click here


The purpose of the monitor result (mode 06) is to allow access to the results for on-board diagnostic monitoring tests of specific components/systems that are not continuously monitored. Examples are catalyst, evaporative emission (EVAP) and thermostat.
The monitor result allows the OBD II scan tool to display the monitor status, test value, minimum test limit and maximum test limit. These data are displayed after the vehicle has been driven to run the monitor.
When the test value is not between the minimum test limit and maximum test limit, the ECM (PCM) interprets this as a malfunction. When the component is not malfunctioning, if the difference of the test value and test limit is very small, the component will malfunction in the near future.
Perform the following instruction to view the monitor status. Although this instruction reference the Lexus/Toyota diagnostic tester, it can be checked using a generic OBD II scan tool. Refer to your scan tool operator's manual for specific procedures.

PERFORM MONITOR DRIVE PATTERN
  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON and the Techstream ON.

  3. Clear DTCs (Click here).

  4. Run the vehicle in accordance with the applicable drive pattern described in READINESS MONITOR DRIVE PATTERN (Click here). Do not turn the ignition switch OFF.

    NOTICE:
    The test results will be lost if the ignition switch is turned OFF.


ACCESS MONITOR RESULT
  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / Result. The monitor status appears after the component name.

    1. Pass: The component is functioning normally.
    2. Fail: The component is malfunctioning.

  2. Confirm that the component is either Pass or Fail.

  3. Select the component and press ENTER. The accuracy test value appears if the monitor status is either Pass or Fail.


CHECK COMPONENT STATUS
  1. Compare the test value with the minimum test limit (MIN LIMIT) and maximum test limit (MAX LIMIT).

  2. If the test value is between the minimum test limit and maximum test limit, the component is functioning normally. If not, the component is malfunctioning. The test value is usually significantly higher or lower than the test limit. If the test value is on the borderline of the test limit, the component will malfunction in the near future.

    HINT:
    The monitor result might on rare occasions be PASS (Pass) even if the malfunction indicator lamp (MIL) is illuminated. This indicates the system malfunctioned on a previous driving cycle. This might be caused by an intermittent problem.


MONITOR RESULT INFORMATION
If you use a generic scan tool, multiply the value by the scaling value listed below.

A/F Sensor Bank 1 Sensor 1:

Monitor ID
Test ID
Scaling
Unit
Description
$01
$8E
Multiply by 0.001
V
A/F sensor deterioration level
$01
$91
Multiply by 0.004
mA
A/F sensor current


A/F Sensor Bank 2 Sensor 1:

Monitor ID
Test ID
Scaling
Unit
Description
$05
$8E
Multiply by 0.001
V
A/F sensor deterioration level
$05
$91
Multiply by 0.004
mA
A/F sensor current


HO2 Sensor Bank 1 Sensor 2:

Monitor ID
Test ID
Scaling
Unit
Description
$02
$07
Multiply by 0.001
V
Minimum sensor voltage
$02
$08
Multiply by 0.001
V
Maximum sensor voltage
$02
$8D
Multiply by 0.001
Seconds
Duration that sensor voltage drops to 0.2 V during fuel cut
$02
$8F
Multiply by 0.0003
g
Maximum oxygen storage capacity


HO2 Sensor Bank 2 Sensor 2:

Monitor ID
Test ID
Scaling
Unit
Description
$06
$07
Multiply by 0.001
V
Minimum sensor voltage
$06
$08
Multiply by 0.001
V
Maximum sensor voltage
$06
$8D
Multiply by 0.001
Seconds
Duration that sensor voltage drops to 0.2 V during fuel cut
$06
$8F
Multiply by 0.0003
g
Maximum oxygen storage capacity


Catalyst - Bank 1:

Monitor ID
Test ID
Scaling
Unit
Description
$21
$A9
Multiply by 0.0003
No dimension
Oxygen storage capacity of catalyst - Bank 1


Catalyst - Bank 2:

Monitor ID
Test ID
Scaling
Unit
Description
$22
$A9
Multiply by 0.0003
No dimension
Oxygen storage capacity of catalyst - Bank 2


EVAP:

Monitor ID
Test ID
Scaling
Unit
Description
$3D
$C9
Multiply by 0.001
kPa
Test value for small leak (P0456)
$3D
$CA
Multiply by 0.001
kPa
Test value for gross leak (P0455)
$3D
$CB
Multiply by 0.001
kPa
Test value for leak detection pump OFF stuck (P2401)
$3D
$CD
Multiply by 0.001
kPa
Test value for leak detection pump ON stuck (P2402)
$3D
$CE
Multiply by 0.001
kPa
Test value for vent valve OFF stuck (P2420)
$3D
$CF
Multiply by 0.001
kPa
Test value for vent valve ON stuck (P2419)
$3D
$D0
Multiply by 0.001
kPa
Test value for reference orifice low flow (P043E)
$3D
$D1
Multiply by 0.001
kPa
Test value for reference orifice high flow (P043F)
$3D
$D4
Multiply by 0.001
kPa
Test value for purge VSV close stuck (P0441)
$3D
$D5
Multiply by 0.001
kPa
Test value for purge VSV open stuck (P0441)
$3D
$D7
Multiply by 0.001
kPa
Test value for purge flow insufficient (P0441)


Rear Oxygen Sensor Heater:

Monitor ID
Test ID
Scaling
Unit
Description
$42
$91
Multiply by 0.001
Ohm
Oxygen sensor heater resistance bank 1 sensor 2
$46
$91
Multiply by 0.001
Ohm
Oxygen sensor heater resistance bank 2 sensor 2


Secondary Air Injection (AIR) - Bank 1:

Monitor ID
Test ID
Scaling
Unit
Description
$71
$E1
Multiply by 0.01
g/sec.
Test value for AIR insufficient
$71
$E2
Multiply by 0.01
kPa
Test value for AIR pump ON stuck
$71
$E3
Multiply by 0.01
kPa
Test value for AIR pump OFF stuck
$71
$E4
Multiply by 0.01
kPa
Test value for AIR valve(s) ON stuck
$71
$E5
Multiply by 0.01
kPa
Test value for AIR valve(s) OFF stuck


Secondary Air Injection (AIR) - Bank 2:

Monitor ID
Test ID
Scaling
Unit
Description
$72
$E1
Multiply by 0.01
g/sec.
Test value for AIR insufficient
$72
$E2
Multiply by 0.01
kPa
Test value for AIR pump ON stuck
$72
$E3
Multiply by 0.01
kPa
Test value for AIR pump OFF stuck
$72
$E4
Multiply by 0.01
kPa
Test value for AIR valve(s) ON stuck
$72
$E5
Multiply by 0.01
kPa
Test value for AIR valve(s) OFF stuck


Misfire:

Monitor ID
Test ID
Scaling
Unit
Description
$A1
$0B
Multiply by 1
Time
Total EWMA misfire count of all cylinders in last ten driving cycles
EWMA: Exponential Weighted Moving Average
$A1
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of all cylinders in last driving cycle is displayed.
  2. While engine is running, total misfire count of all cylinders in current driving cycle is displayed.
$A2
$0B
Multiply by 1
Time
Total EWMA misfire count of cylinder 1 in last ten driving cycles
$A2
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of cylinder 1 in last driving cycle is displayed.
  2. While engine is running, total misfire count of cylinder 1 in current driving cycle is displayed.
$A3
$0B
Multiply by 1
Time
Total EWMA misfire count of cylinder 2 in last ten driving cycles
$A3
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of cylinder 2 in last driving cycle is displayed.
  2. While engine is running, total misfire count of cylinder 2 in current driving cycle is displayed.
$A4
$0B
Multiply by 1
Time
Total EWMA misfire count of cylinder 3 in last ten driving cycles
$A4
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of cylinder 3 in last driving cycle is displayed.
  2. While engine is running, total misfire count of cylinder 3 in current driving cycle is displayed.
$A5
$0B
Multiply by 1
Time
Total EWMA misfire count of cylinder 4 in last ten driving cycles
$A5
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of cylinder 4 in last driving cycle is displayed.
  2. While engine is running, total misfire count of cylinder 4 in current driving cycle is displayed.
$A6
$0B
Multiply by 1
Time
Total EWMA misfire count of cylinder 5 in last ten driving cycles
$A6
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of cylinder 5 in last driving cycle is displayed.
  2. While engine is running, total misfire count of cylinder 5 in current driving cycle is displayed.
$A7
$0B
Multiply by 1
Time
Total EWMA misfire count of cylinder 6 in last ten driving cycles
$A7
$0C
Multiply by 1
Time
  1. When ignition switch is ON, total misfire count of cylinder 6 in last driving cycle is displayed.
  2. While engine is running, total misfire count of cylinder 6 in current driving cycle is displayed.