LABEL (Tester Display)
| Measurement Item
| Diagnostic Note
|
Vehicle Speed
| Vehicle speed
| Speed indicated on speedometer
|
Engine Speed
| Engine speed
| -
|
Calculate Load
| Calculated load
| Calculated load by ECM
|
Vehicle Load
| Vehicle load
| -
|
MAF
| Mass air flow volume
| If approximately 0.0 g/sec.:
- Mass air flow meter power source circuit open or short
- VG circuit open or short
If 160.0 g/sec. or more:
- E2G circuit open
|
Atmosphere Pressure
| Atmosphere pressure
| -
|
Coolant Temp
| Engine coolant temperature
| If value -40°C (-40°F), sensor circuit open If value 140°C (284°F) or more, sensor circuit shorted
|
Intake Air
| Intake air temperature
| If value -40°C (-40°F), sensor circuit open If value 140°C (284°F) or more, sensor circuit shorted
|
Engine Run Time
| Accumulated engine running time
| -
|
Initial Engine Coolant Temp
| Initial engine coolant temperature
| -
|
Initial Intake Air Temp
| Initial intake air temperature
| -
|
Battery Voltage
| Battery voltage
| -
|
Accel Sens. No.1 Volt %
| Absolute Accelerator Pedal Position (APP) No. 1
| -
|
Accel Sens. No.2 Volt %
| Absolute APP No. 2
| -
|
Throttle Sensor Volt %
| Throttle sensor positioning
| -
|
Throttl Sensor #2 Volt %
| Absolute throttle sensor positioning #2
| -
|
Throttle Sensor Position
| Throttle position
| -
|
Throttle Motor DUTY
| Throttle actuator duty
| -
|
Injector (Port)
| Injection period of No. 1 cylinder
| -
|
Injection Volum (Cylinder1)
| Injection volume
| -
|
Fuel Pump/Speed Status
| Fuel pump/speed status
| -
|
Vacuum Pump
| Key-off EVAP system leak detection pump status
| Refer to EVAP System (Click here)
|
EVAP (Purge) VSV
| EVAP purge VSV duty ratio
| -
|
Evap Purge Flow
| Ratio of evaporative purge flow to intake air volume
| -
|
Purge Density Learn Value
| Learning value of purge density
| -
|
EVAP System Vent Value
| Key-off EVAP system vent valve status
| -
|
EVAP Purge VSV
| EVAP Purge VSV
| -
|
Target Air-Fuel Ratio
| Ratio compared to stoichiometric level
| -
|
AF Lambda B1S1
| Fuel trim at A/F sensor
| -
|
AF Lambda B2S1
| Fuel trim at A/F sensor
| -
|
AFS Voltage B1S1
| A/F sensor output voltage
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
AFS Voltage B2S1
| A/F sensor output voltage
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
AFS Current B1S1
| A/F sensor current
| -
|
AFS Current B2S1
| A/F sensor current
| -
|
O2S B1S2
| Heated oxygen sensor output voltage
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
O2S B2S2
| Heated oxygen sensor output voltage
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
O2S Impedance B1S2
| Sub heated oxygen sensor impedance (bank 1 sensor 2)
| -
|
O2S Impedance B2S2
| Sub heated oxygen sensor impedance (bank 2 sensor 2)
| -
|
Short FT #1
| Short-term fuel trim
| Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
|
Long FT #1
| Long-term fuel trim
| Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve
|
Total FT #1
| Total fuel trim (bank 1)
| -
|
Short FT #2
| Short-term fuel trim
| Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
|
Long FT #2
| Long-term fuel trim
| Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve
|
Total FT #2
| Total fuel trim (bank 2)
| -
|
Fuel System Status #1
| Fuel system status (bank 1)
| - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OLDrive: Open loop due to driving conditions (fuel enrichment)
- OLFault: Open loop due to detected system fault
- CLFault: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
|
Fuel System Status #2
| Fuel system status (bank 2)
| - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OLDrive: Open loop due to driving conditions (fuel enrichment)
- OLFault: Open loop due to detected system fault
- CLFault: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
|
Air pump pressure (absolute)
| Air pump pressure (absolute)
| -
|
Air Pump2 Pressure (Absolute)
| Air pump 2 pressure (absolute)
| -
|
Air Pump Pulsation Pressure
| Air pump pulsation pressure
| -
|
Air Pump2 Pulsation Pressure
| Air pump 2 pulsation pressure
| -
|
Secondary Air Control VSV
| Secondary air injection system status
| -
|
2nd Air System Status
| Second air system status
| -
|
AI Test
| Secondary air injection system operation prohibit
| -
|
IGN Advance
| Ignition advance
| -
|
Knock Feedback Value
| Feedback value of knocking
| -
|
Knock Correct Learn Value
| Correction learning value of knocking
| -
|
ACIS VSV
| VSV for Acoustic Control Induction System (ACIS)
| -
|
VVT Control Status #1
| VVT control status
| -
|
VVT Control Status #2
| VVT control status
| -
|
Catalyst Temp B1S1
| Estimated catalyst temperature (bank 1 sensor 1)
| -
|
Catalyst Temp B2S1
| Estimated catalyst temperature (bank 2 sensor 1)
| -
|
Catalyst Temp B1S2
| Estimated catalyst temperature (bank 1 sensor 2)
| -
|
Catalyst Temp B2S2
| Estimated catalyst temperature (bank 2 sensor 2)
| -
|
Starter Signal
| Starter switch signal
| -
|
Starter Control
| Starter switch status
| -
|
Power Steering Signal Record
| Power steering switch status
| -
|
Starter Relay
| Starter relay status
| -
|
Power Steer. Sig. Record
| Power steering signal (history)
| -
|
ACC Relay
| ACC relay status
| -
|
Neutral Position SW Signal
| Park / Neutral position (PNP) switch signal
| -
|
Stop Light Switch
| Stop light switch
| -
|
A/C Signal
| A/C signal
| -
|
Closed Throttle Position SW
| Closed throttle position switch
| -
|
Fuel Cut Condition
| Fuel cut condition
| -
|
Electrical Load Signal
| Electrical load signal
| -
|
Time after DTC Cleared
| Cumulative time after DTC cleared
| -
|
Distance from DTC Cleared
| Accumulated distance from DTC cleared
| -
|
Warmup Cycle Cleared DTC
| Warm-up cycle after DTC cleared
| -
|
TC and TE1
| TC and CG (TE1) terminals of DLC3
| -
|
Ignition Trig. Count
| Ignition counter
| -
|
Cylinder #1 Misfire Count
| Cylinder #1 misfire
| Only displayed during idling
|
Cylinder #2 Misfire Count
| Cylinder #2 misfire
| Only displayed during idling
|
Cylinder #3 Misfire Count
| Cylinder #3 misfire
| Only displayed during idling
|
Cylinder #4 Misfire Count
| Cylinder #4 misfire
| Only displayed during idling
|
Cylinder #5 Misfire Count
| Cylinder #5 misfire
| Only displayed during idling
|
Cylinder #6 Misfire Count
| Cylinder #6 misfire
| Only displayed during idling
|
All Cylinders Misfire Count
| All cylinders misfire
| Only displayed during idling
|
Misfire RPM
| Engine speed when misfire occurred
| -
|
Misfire Load
| Engine load when misfire occurred
| -
|
Misfire Margin
| Margin to detect engine misfire
| -
|
Catalyst OT MF F/C
| Catalyst over temperature Misfire prevention fuel cut
| -
|
Cat OT MF F/C History
| Catalyst over temperature Misfire prevention fuel cut history:
| -
|
Cat OT MF F/C Cylinder#1
| Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#2
| Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#3
| Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#4
| Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#5
| Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#6
| Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
| -
|
ACT VSV
| A/C cut status for Active Test
| -
|
Idle Fuel Cut
| Fuel cut idle
| ON: when throttle valve fully closed and engine speed over 3500 rpm
|
FC TAU
| Fuel cut during very light load
| Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
|
SPD (NT)
| Input shaft speed
| Data is displayed in increments of 50 rpm.
|
SPD (SP2)
| Output shaft speed
| -
|