Home › TRANSMISSION ยท AB60F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up is:
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever on N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On P or N: ON
    2. Not on P or N: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal is:
    1. Depressed: ON
    2. Released: OFF
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Shift lever position is:
    1. On D: 1st, 2nd, 3rd, 4th, 5th or 6th
    2. On S: 1st, 2nd, 3rd, 4th, 5th or 6th
    -
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On R: ON
    2. Not on R: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On P: ON
    2. Not on P: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On N: ON
    2. Not on N: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On D: ON
    2. Not on D: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever position is:
    1. ON: S, "+" or "-"
    2. OFF: Not on S, "+" or "-"
    -
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted
    Lock Up
    Lock-up/
    ON or OFF
    Lock-up is:
    1. Operating: ON
    2. Not operating: OFF
    -
    Lock Up Solenoid Status
    Lock-up solenoid status/
    ON or OFF
    Lock-up solenoid is:
    1. Operating: ON
    2. Not operating: OFF
    -
    SLU Solenoid Status
    Shift solenoid SLU status/
    ON or OFF
    Shift solenoid SLU is:
    1. Operating: ON
    2. Not operating: OFF
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Engine and ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate shift solenoid SLU
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Solenoid (SLT)*
    Operate shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate shift solenoid S1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Solenoid (S2)
    Operate shift solenoid S2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Solenoid (S3)
    Operate shift solenoid S3
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Solenoid (S4)
    Operate shift solenoid S4
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up condition
    ON or OFF
    Possible to check shift solenoid valve SLU operation
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (37 mph) or more
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (31 mph) or less
    Activate the Solenoid (SR)
    Operate shift solenoid SR
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Solenoid (SL1)
    Operate shift solenoid SL1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Activate the Solenoid (SL2)
    Operate shift solenoid SL2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well. Note that the pressure values in the Active Test and HYDRAULIC TEST are different.