DTC P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0756 |
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 6th. |
|
| P0756 |
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 5th. |
|
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under S2 stuck ON malfunction | 1st | 2nd | 2nd | 4th | 6th | 6th |
| *2: Actual gear position under S2 stuck OFF malfunction | 3rd | 3rd | 3rd | 4th | 5th | 5th |
| Related DTCs | P0756: Shift solenoid valve S2/OFF malfunction Shift solenoid valve S2/ON malfunction |
| Required sensors/Components | Shift solenoid valve S2 |
| Frequency of operation | Continuous |
| Duration | 0.4 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | None |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve S3 circuit | Not circuit malfunction |
| Shift solenoid valve S4 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0°crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 1st |
| Vehicle speed | 2 km/h (1.2 mph) or more and less than 40 km/h (24.9 mph) |
| Engine speed - Turbine speed (NE - NT) | 50 rpm or more |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Turbine speed/Output speed (NT/NO) | 1.24 or more, and 1.49 or less (This means actual gear is 3rd) |
| Turbine speed/Output speed (NT/NO) | 0.66 or more, and 0.80 or less (This means actual gear is 5th) |
| Turbine speed/Output speed (NT/NO) | 0.51 or more, and 0.65 or less (This means actual gear is 6th) |
| Turbine speed/Output speed (NT/NO) | 0.51 or more, and 0.65 or less (This means actual gear is 6th) |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (31 mph) or less |
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve S2 | ON | ON | OFF | OFF | OFF | ON |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0756) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0756 is output | A |
| P0756 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE S2 |
![]() |
Remove shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body | 20°C (68°F) | 11 to 15 Ω |
Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||