Home › TRANSMISSION · A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION


C159071E02

The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the duty ratio* of the SLT solenoid valve to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

HINT:
*: The duty ratio is the ratio of the current ON time (A) to the total of the current ON and OFF time (A + B).
Duty Ratio (%) = A / (A + B) x 100


DTC Code
DTC Detection Condition
Trouble Area
P2714
The ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the output shaft, and also by the oil pressure. (2-trip detection logic)
  1. Shift solenoid valve SLT remains open or closed
  2. Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed
  3. 1-2 shift valve is stuck
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and stores these DTCs when the amount of heat absorption exceeds the specified value.
There are two reasons that make the revolution different:
  1. When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.
  2. When the shift solenoid valve remains on or off, the gear position commanded by the ECM and the actual gear position are not the same.

NOTICE:
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


MONITOR STRATEGY


Related DTCs
P2714: Shift solenoid valve SLT/ON malfunction
Required sensors/Components
Shift solenoid valve SLT, Valve body, ATF temperature sensor, Speed sensor (NT), Speed sensor (SP2)
Frequency of operation
Continuous
Duration
Immediately
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Turbine speed sensor circuit
Not circuit malfunction
Output speed sensor circuit
Not circuit malfunction
ATF temperature sensor "A" circuit
Not circuit malfunction
Shift solenoid valve S1 circuit
Not circuit malfunction
Shift solenoid valve S2 circuit
Not circuit malfunction
Shift solenoid valve SR circuit
Not circuit malfunction
Shift solenoid valve SL1 circuit
Not circuit malfunction
Shift solenoid valve SL2 circuit
Not circuit malfunction
Shift solenoid valve SLT circuit
Not circuit malfunction
ECT (Engine Coolant Temperature) sensor circuit
Not circuit malfunction
KCS sensor circuit
Not circuit malfunction
ETCS (Electric Throttle Control System)
Not system down
Transmission position
"D"
Duration time from shifting "N" to "D"
4 seconds or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by KCS control
0° crankshaft angle or more
Engine
Starting

Transfer Position is 4WD HIGH* 
Vehicle speed sensor circuit
Not circuit malfunction
Output shaft speed sensor circuit
Not circuit malfunction
Transfer output speed
143 rpm or more
NO/NOtf (Transfer input speed/Transfer output speed)
0.9 or more, and less than 1.1

HINT:
*: This condition only applies to 4WD.


TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met: ON malfunction (A), (B), (C), (D), (E), (F) or (G)

ON Malfunction (A) 
Summation of C1 clutch heat generations
Specified value

ON Malfunction (B) 
Shift solenoid valve S1 ON malfunction
Detected

ON Malfunction (C) 
Shift solenoid valve S2 ON malfunction
Detected

ON Malfunction (D) 
Shift solenoid valve SR OFF malfunction
Detected

ON Malfunction (E) 
1-2 shift valve malfunction
Detected

ON Malfunction (F) 
Shift solenoid valve SL1 OFF malfunction
Detected

ON Malfunction (G) 
Shift solenoid valve SL2 ON malfunction
Detected

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P2714 is output
    A
    P2714 and other DTCs are output
    B

    HINT:
    If any other codes besides P2714 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C159068E01
  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

  1. Measure the line pressure.

    ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.

OK:
The line pressure changes as specified when performing the Active Test.



NG
Go to step 9
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST)

CAUTION:
This test should always be performed with at least 2 people.

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Perform the test with the A/C turned off.

  1. Connect the Techstream to the DLC3.

  1. Clear the DTC (Click here).

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.


    ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (31 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the Techstream.

  1. Compare the ECM gear shift command and the actual gear position.

    OK:
    Gear position changes in accordance with the Techstream command.


    Result 
    System Condition
    ECM Gear Shift Command
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    Malfunction
    Shift solenoid S1
    Stuck ON
    1st
    2nd
    2nd
    1st
    N*1
    A
    Stuck OFF
    4th
    3rd
    3rd
    4th
    5th
    Shift solenoid S2
    Stuck ON*2
    2nd
    2nd
    3rd
    3rd
    N*1
    B
    Stuck OFF*3
    1st
    1st
    4th
    4th
    5th
    Shift solenoid SL2
    Stuck ON
    1st
    2nd
    3rd
    4th
    N*1
    C
    Stuck OFF
    1st
    2nd
    3rd
    4th
    5th
    Shift solenoid SR
    Stuck ON*4
    1st
    2nd
    3rd
    4th
    5th
    D
    Stuck OFF*5
    1st
    2nd
    3rd
    4th
    4th
    Normal
    1st
    2nd
    3rd
    4th
    5th
    E

    HINT:
    1. *1: Neutral
    2. *2: When shift solenoid S2 is stuck ON, the vehicle cannot drive in reverse.
    3. *3: When shift solenoid S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also, the 5th to 4th down-shift will have time lag.
    4. *4: Stuck ON condition can be determined by checking if shift shock has increased excessively.
    5. *5: When shift solenoid SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
    6. Gear shifts can be determined by paying attention to changes in rpm.



B
Go to step 5

C
Go to step 6

D
Go to step 7

E
Go to step 9
A


4.INSPECT SHIFT SOLENOID VALVE S1


    C159062E01
  1. Remove shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid S1 connector - Shift solenoid S1 body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A

REPLACE SHIFT SOLENOID VALVE S1  

5.INSPECT SHIFT SOLENOID VALVE S2


    A110987E08
  1. Remove shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid S2 connector - Shift solenoid S2 body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A

REPLACE SHIFT SOLENOID VALVE S2  

6.INSPECT SHIFT SOLENOID VALVE SL2


    C151311E17
  1. Remove shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal 1 of shift solenoid valve SL2 - terminal 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A

REPLACE SHIFT SOLENOID VALVE SL2  

7.INSPECT SHIFT SOLENOID VALVE SR


    A110988E08
  1. Remove shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid SR connector - Shift solenoid SR body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SR
OK


8.INSPECT SHIFT SOLENOID VALVE SL1


    C151311E16
  1. Remove shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal 1 of shift solenoid valve SL1 - terminal 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A

REPLACE SHIFT SOLENOID VALVE SL1  

9.INSPECT SHIFT SOLENOID VALVE SLT


    C162477E01
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal 1 of shift solenoid valve SLT - terminal 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


10.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


11.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)