Home › TRANSMISSION · AB60F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2716    Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

Refer to DTC P0894 .

DTC Code
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic)
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM
Reference: Inspect using an oscilloscope.
Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
D74-9 (SLT+) - D74-8 (SLT-)
5 V/DIV., 1 msec./ DIV.
Engine is idling
Refer to the illustration

C140833E01

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P2716: Shift solenoid valve SLT/Range check
Required sensors/Components
Shift solenoid valve SLT
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
None
Solenoid current cut status
Not cut
Battery voltage
11 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Solenoid status from MIC
Failure

COMPONENT OPERATING RANGE


Output signal duty
Less than 100%

WIRING DIAGRAM


C161203E16


INSPECTION PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)


    C159421E14
  1. Disconnect the D63 No. 1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    13 (SLT+) - 5 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    13 (SLT+) - Body ground
    Always
    10 kΩ or higher
    5 (SLT-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
C159422E26
  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D74-9 (SLT+) - D74-8 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    D74-9 (SLT+) - Body ground
    Always
    10 kΩ or higher
    D74-8 (SLT-) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 3UR-FE)
    B
    OK (for 3UR-FBE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

3.INSPECT SHIFT SOLENOID VALVE SLT
C162477E01
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE (Click here)