Home › ENGINE · 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using the Techstream.

Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF


DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. IGN fuse
  4. Stop light switch
  5. ECM

WIRING DIAGRAM


A164732E01


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream ON.
    4. Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.
    5. Check the STP signal when the brake pedal is depressed and released.


Brake Pedal Operation
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF
1.CHECK STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
A148738E04
  1. Disconnect the A4 stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 - Body ground
    Always
    11 to 14 V
    A4-3 - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 4
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E13
  1. Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin not pushed
    10 kΩ or higher
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3.CHECK ECM (STP AND ST1 - VOLTAGE)
A112585E22
  1. Disconnect the A24 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-35 (ST1-) - Body ground
    Brake pedal released
    11 to 14 V
    Brake pedal depressed
    0 to 3 V
    A24-36 (STP) - Body ground
    Brake pedal released
    0 to 3 V
    Brake pedal depressed
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.INSPECT FUSE (STOP AND IGN)
A162281E01
  1. Remove the STOP and IGN fuses from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω
    IGN fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH)