DTC P0351 Ignition Coil "A" Primary / Secondary Circuit |
DTC P0352 Ignition Coil "B" Primary / Secondary Circuit |
DTC P0353 Ignition Coil "C" Primary / Secondary Circuit |
DTC P0354 Ignition Coil "D" Primary / Secondary Circuit |
DTC P0355 Ignition Coil "E" Primary / Secondary Circuit |
DTC P0356 Ignition Coil "F" Primary / Secondary Circuit |
DTC P0357 Ignition Coil "G" Primary / Secondary Circuit |
DTC P0358 Ignition Coil "H" Primary / Secondary Circuit |

| DTC Code | DTC Detection Condition | Trouble Area |
| P0351 P0352 P0353 P0354 P0355 P0356 P0357 P0358 | No IGF signal to ECM while engine running (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D74-40 (IGT1) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-33 (IGT2) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-37 (IGT3) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-34 (IGT4) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-35 (IGT5) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-36 (IGT6) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-38 (IGT7) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-39 (IGT8) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-104 (IGF1) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |
| D74-105 (IGF2) - D74-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling | The correct waveform is as shown |

| Related DTCs | P0351: Igniter (cylinder 1) malfunction P0352: Igniter (cylinder 2) malfunction P0353: Igniter (cylinder 3) malfunction P0354: Igniter (cylinder 4) malfunction P0355: Igniter (cylinder 5) malfunction P0356: Igniter (cylinder 6) malfunction P0357: Igniter (cylinder 7) malfunction P0358: Igniter (cylinder 8) malfunction |
| Required Sensors/Components (Main) | Igniter |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | About 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions A or B met | - |
| A. Engine RPM | 1500 rpm or less |
| B. Starter | OFF |
| Either of following conditions C or D met | - |
| C. Both of following conditions (a) and (b) met | - |
| (a) Engine speed | 500 rpm or less |
| (b) Battery voltage | 6 V or more |
| D. All of following conditions (a), (b) and (c) met | - |
| (a) Engine speed | More than 500 rpm |
| (b) Battery voltage | 10 V or more |
| (c) Number of sparks after CPU reset | 5 sparks or more |
| IGF signal | ECM does not receive any IGF signal despite ECM sending IGT signal to igniter |
| IGF signal | Igniter transmits IGF signal when it receives IGT signal from ECM |


| 1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the D10, D12, D14, D16, D19, D21, D23 or D25 ignition coil with igniter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D10-4 (GND) - Body ground | Always | Below 1 Ω |
| D25-4 (GND) - Body ground | Always | Below 1 Ω |
| D12-4 (GND) - Body ground | Always | Below 1 Ω |
| D23-4 (GND) - Body ground | Always | Below 1 Ω |
| D14-4 (GND) - Body ground | Always | Below 1 Ω |
| D21-4 (GND) - Body ground | Always | Below 1 Ω |
| D16-4 (GND) - Body ground | Always | Below 1 Ω |
| D19-4 (GND) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D10-1 (+B) - D10-4 (GND) | Ignition switch ON | 11 to 14 V |
| D25-1 (+B) - D25-4 (GND) | Ignition switch ON | 11 to 14 V |
| D12-1 (+B) - D12-4 (GND) | Ignition switch ON | 11 to 14 V |
| D23-1 (+B) - D23-4 (GND) | Ignition switch ON | 11 to 14 V |
| D14-1 (+B) - D14-4 (GND) | Ignition switch ON | 11 to 14 V |
| D21-1 (+B) - D21-4 (GND) | Ignition switch ON | 11 to 14 V |
| D16-1 (+B) - D16-4 (GND) | Ignition switch ON | 11 to 14 V |
| D19-1 (+B) - D19-4 (GND) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
![]() |
Disconnect the D10, D12, D14, D16, D19, D21, D23 or D25 ignition coil with igniter connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D10-2 (IGF1) - D74-104 (IGF1) | Always | Below 1 Ω |
| D25-2 (IGF2) - D74-105 (IGF2) | Always | Below 1 Ω |
| D12-2 (IGF2) - D74-105 (IGF2) | Always | Below 1 Ω |
| D23-2 (IGF1) - D74-104 (IGF1) | Always | Below 1 Ω |
| D14-2 (IGF2) - D74-105 (IGF2) | Always | Below 1 Ω |
| D21-2 (IGF1) - D74-104 (IGF1) | Always | Below 1 Ω |
| D16-2 (IGF1) - D74-104 (IGF1) | Always | Below 1 Ω |
| D19-2 (IGF2) - D74-105 (IGF2) | Always | Below 1 Ω |
| D10-3 (IGT1) - D74-40 (IGT1) | Always | Below 1 Ω |
| D25-3 (IGT2) - D74-33 (IGT2) | Always | Below 1 Ω |
| D12-3 (IGT3) - D74-37 (IGT3) | Always | Below 1 Ω |
| D23-3 (IGT4) - D74-34 (IGT4) | Always | Below 1 Ω |
| D14-3 (IGT5) - D74-35 (IGT5) | Always | Below 1 Ω |
| D21-3 (IGT6) - D74-36 (IGT6) | Always | Below 1 Ω |
| D16-3 (IGT7) - D74-38 (IGT7) | Always | Below 1 Ω |
| D19-3 (IGT8) - D74-39 (IGT8) | Always | Below 1 Ω |
| D10-2 (IGF1) or D74-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D25-2 (IGF2) or D74-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D12-2 (IGF2) or D74-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D23-2 (IGF1) or D74-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D14-2 (IGF2) or D74-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D21-2 (IGF1) or D74-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D16-2 (IGF1) or D74-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D19-2 (IGF2) or D74-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D10-3 (IGT1) or D74-40 (IGT1) - Body ground | Always | 10 kΩ or higher |
| D25-3 (IGT2) or D74-33 (IGT2) - Body ground | Always | 10 kΩ or higher |
| D12-3 (IGT3) or D74-37 (IGT3) - Body ground | Always | 10 kΩ or higher |
| D23-3 (IGT4) or D74-34 (IGT4) - Body ground | Always | 10 kΩ or higher |
| D14-3 (IGT5) or D74-35 (IGT5) - Body ground | Always | 10 kΩ or higher |
| D21-3 (IGT6) or D74-36 (IGT6) - Body ground | Always | 10 kΩ or higher |
| D16-3 (IGT7) or D74-38 (IGT7) - Body ground | Always | 10 kΩ or higher |
| D19-3 (IGT8) or D74-39 (IGT8) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Clear DTCs (Click here).
Shuffle the arrangement of the ignition coils with igniters (among No. 1 to No. 8 cylinders).
Perform a simulation test.
Check DTCs displayed on the Techstream.
| Result | Proceed to |
| Same DTC is output | A |
| Different ignition coil DTC is output | B |
|
| ||||
| A | ||
| ||