DTC P0781 1-2 Shift (1-2 Shift Valve) |

| DTC Code | DTC Detection Condition | Trouble Area |
| P0781 |
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd. (c) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips). |
|
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Actual gear position under malfunction | 1st | 1st | 3rd | 3rd | N* | N* |
| Gear position under normal conditions | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Actual gear position under fail-safe mode | 1st* | 1st* | 3rd | 3rd | 3rd | 3rd |
| Related DTCs | P0781: Valve body/Rationality check |
| Required sensors/Components | Valve body, Automatic transmission assembly |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (B) 0.4 seconds Condition (C) 3 seconds Condition (D) 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | None |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve S3 circuit | Not circuit malfunction |
| Shift solenoid valve S4 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed -Turbine speed (NE - NT) (After transition to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition to 5th gear) | Less than 100 km/h (62.2 mph) |
| Turbine speed/Output speed (NT/NO) | 3.11 or more, and 7.58 or less (This means actual gear is 1st) |
| Turbine speed/Output speed (NT/NO) | 1.24 or more, and 1.49 or less (This means actual gear is 3rd) |
| Turbine speed - Output speed x 4th gear ratio (NT - NO x 4th gear ratio) | 1000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1000 rpm or more |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0781) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0781 is output | A |
| P0781 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST) |
Connect the Techstream to the DLC3.
Clear the DTC (Click here).
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (31 mph) or less |
| Techstream gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Actual gear position under malfunction | 1st | 1st | 3rd | 3rd | N* | N* |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
|
| ||||
| OK | |
| 4.CLEAR DTC AND PERFORM RUNNING TEST |
Clear the DTC (Click here).
Check for DTC again after conducting the MONITOR DRIVE PATTERN (Click here).
|
| ||||
| OK | ||
| ||