OCCUPANT CLASSIFICATION SYSTEM > TERMINALS OF ECU |
| CHECK OCCUPANT CLASSIFICATION ECU |

| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specification |
| Y2-1 (+B) - Y2-3 (GND)*1 Q11-1 (+B) - Q11-3 (GND)*2 | R - W-B | Battery | Ignition switch ON | 11 to 14 V |
| Y2-2 (DIA) - Y2-3 (GND)*1 Q11-2 (DIA) - Q11-3 (GND)*2 | BR - W-B | Diagnosis (DLC3) | Ignition switch ON | Pulse generation |
| Y2-3 (GND) - Body ground*1 Q11-3 (GND) - Body ground*2 | W-B - Body ground | Ground | Always | Below 1 Ω |
| Y2-4- (FSR-) - Y2-3 (GND)*1 Q11-4- (FSR-) - Q11-3 (GND)*2 | B - W-B | Center airbag sensor communication ground line | Always | Below 1 Ω |
| Y2-5 (BGND) - Y2-3 (GND)*1 Q11-5 (BGND) - Q11-3 (GND)*2 | BE - W-B | Passenger side buckle switch ground line | Always | Below 1 Ω |
| Y2-7 (IG) - Y2-3 (GND)*1 Q11-7 (IG) - Q11-3 (GND)*2 | SB - W-B | Power source (IGN fuse) | Ignition switch ON | 11 to 14 V |
| Y2-8 (FSR+) - Y2-4 (FSR-)*1 Q11-8 (FSR+) - Q11-4 (FSR-)*2 | W - B | Center airbag sensor communication line | Ignition switch ON | Pulse generation |
| Y2-9 (BSW) - Y2-5 (BGND)*1 Q11-9 (BSW) - Q11-5 (BGND)*2 | L - BE | Passenger side buckle switch line | Buckle switch ON | 0.12 to 0.18 A |
| Buckle switch OFF | 0.4 to 0.7 mA | |||
| Y1-1 (SGD1) - Y2-3 (GND)*1 Y1-1 (SGD1) - Q11-3 (GND)*2 | Y - W-B | Front occupant detection sensor LH ground line | Always | Below 1 Ω |
| Y1-2 (SGD2) - Y2-3 (GND)*1 Y1-2 (SGD2) - Q11-3 (GND)*2 | SB - W-B | Front occupant detection sensor RH ground line | Always | Below 1 Ω |
| Y1-3 (SGD3) - Y2-3 (GND)*1 Y1-3 (SGD3) - Q11-3 (GND)*2 | L - W-B | Rear occupant detection sensor LH ground line | Always | Below 1 Ω |
| Y1-4 (SGD4) - Y2-3 (GND)*1 Y1-4 (SGD4) - Q11-3 (GND)*2 | W - W-B | Rear occupant detection sensor RH ground line | Always | Below 1 Ω |
| Y1-11 (SVC1) - Y1-1 (SGD1) | P - Y | Front occupant detection sensor LH power supply line | Ignition switch ON, load is applied to front occupant detection sensor LH | 4.5 to 5.1 V |
| Y1-12 (SVC2) - Y1-2 (SGD2) | BR - SB | Front occupant detection sensor RH power supply line | Ignition switch ON, load is applied to front occupant detection sensor RH | 4.5 to 5.1 V |
| Y1-5 (SVC3) - Y1-3 (SGD3) | R - L | Rear occupant detection sensor LH power supply line | Ignition switch ON, load is applied to rear occupant detection sensor LH | 4.5 to 5.1 V |
| Y1-6 (SVC4) - Y1-4 (SGD4) | B - W | Rear occupant detection sensor RH power supply line | Ignition switch ON, load is applied to rear occupant detection sensor RH | 4.5 to 5.1 V |
| Y1-7 (SIG1) - Y1-1 (SGD1) | BE - Y | Front occupant detection sensor LH signal line | Ignition switch ON, load is applied to front occupant detection sensor LH | Pulse generation |
| Y1-8 (SIG2) - Y1-2 (SGD2) | GR - SB | Front occupant detection sensor RH signal line | Ignition switch ON, load is applied to front occupant detection sensor RH | Pulse generation |
| Y1-9 (SIG3) - Y1-3 (SGD3) | G - L | Rear occupant detection sensor LH signal line | Ignition switch ON, load is applied to rear occupant detection sensor LH | Pulse generation |
| Y1-10 (SIG4) - Y1-4 (SGD4) | V - W | Rear occupant detection sensor RH signal line | Ignition switch ON, load is applied to rear occupant detection sensor RH | Pulse generation |