Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH


    C155869
  1. Remove the nut, spring washer and control shaft lever RH.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    D027903E01
  1. Using a screwdriver, pry out the lock washer.

  1. Remove the nut, lock washer and bolt.

  1. Remove the park/neutral position switch.



3. REMOVE OIL COOLER TUBE UNION


    C158384
  1. Remove the 2 oil cooler tube unions.

  1. Remove the 2 O-rings from each oil cooler tube union.



4. REMOVE SPEED SENSOR


    C111258
  1. Remove the 2 bolts and 2 speed sensors.

  1. Remove the 2 O-rings from each sensor.



5. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE


C117463
  1. Remove the 2 bolts.

  1. Remove the breather tube.

  1. Remove the O-ring from the tube.



6. REMOVE AUTOMATIC TRANSMISSION HOUSING


    C159645
  1. Remove the 10 bolts.

  1. Remove the transmission housing.



7. REMOVE TRANSMISSION CASE ADAPTER SUB-ASSEMBLY


C117456E01
  1. Remove the 8 bolts.

  1. Remove the transmission case adapter.

    HINT:
    Use a brass bar and a hammer to remove the transmission case adapter.



8. REMOVE TRANSMISSION CASE ADAPTER OIL SEAL


    C117454E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the transmission case. Wrap the tip of the screwdriver with tape.



9. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY


    D027911E01
  1. Install the transmission case on the overhaul attachment.



10. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.

  1. Remove the drain plug and 20 bolts.



11. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    D001124E01
  1. Remove the magnets, and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear
    2. Brass (non-magnetic): bushing wear



12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    D012703E01
  1. Turn over the transmission.

  1. Remove the 4 bolts and oil strainer from the valve body.

  1. Remove the O-ring from the oil strainer.



13. REMOVE TRANSMISSION WIRE


D012704E01
  1. Remove the 2 bolts and 2 clamps, and disconnect the 2 ATF temperature sensors.

  1. Disconnect the 7 connectors from the solenoid valves.



    D027912E01
  1. Remove the bolt from the case.

  1. Pull the transmission wire out of the transmission case.

  1. Remove the O-ring from the transmission wire.



14. REMOVE TRANSMISSION VALVE BODY ASSEMBLY
  1. Remove the bolt, detent spring cover and detent spring.



    C157292E02
  1. Remove the 19 bolts.

  1. Remove the valve body.



15. REMOVE TRANSMISSION CASE GASKET


    D027968E03
  1. Remove the 3 gaskets.



16. REMOVE BRAKE DRUM GASKET


    D027969E01
  1. Remove the 3 gaskets.



17. REMOVE CHECK BALL BODY


    D027914E04
  1. Remove the check ball body and spring.



18. REMOVE C-2 ACCUMULATOR PISTON


    D027915E01
  1. While applying compressed air to the oil hole, remove the C2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 and B-3 accumulator pistons may jump out.



19. REMOVE B-3 ACCUMULATOR PISTON


    D027915E01
  1. While applying compressed air to the oil hole, remove the B3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.

    NOTICE:
    Be careful as the C-3 accumulator piston may jump out.



20. REMOVE C-3 ACCUMULATOR PISTON


    D027916E01
  1. While applying compressed air to the oil hole, remove the C3 accumulator piston and 2 springs.

  1. Remove the 2 O-rings from the piston.



21. REMOVE C-1 ACCUMULATOR VALVE


    D027917E01
  1. Remove the C-1 accumulator valve and 2 springs.



22. REMOVE PARKING LOCK PAWL BRACKET


    D012708E01
  1. Remove the 3 bolts and bracket.



23. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    D012709E01
  1. Disconnect the parking lock rod from the manual valve lever.



24. REMOVE PARKING LOCK PAWL SHAFT


    D028846E01
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

  1. Remove the E-ring from the shaft.



25. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    D027918E01
  1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.



    D027919E01
  1. Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the transmission case.

  1. Pull the manual valve lever shaft out through the case, and remove the manual valve lever.



26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    D027920E02
  1. Using a screwdriver, pry out the 2 oil seals.

    NOTICE:
    Be careful not to damage the transmission case. Wrap the tip of the screwdriver with tape.



27. REMOVE OIL PUMP ASSEMBLY


    D027921E01
  1. Remove the 10 bolts.



    D027922E02
  1. Using SST, remove the oil pump.

    SST
    09350-30020   (09350-07020)



    D028809E01
  1. Remove the No. 1 thrust bearing race from the front oil pump.



28. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    D027923E01
  1. Remove the clutch drum and input shaft drum assembly from the transmission case.



    D027924E03
  1. Remove the clutch drum thrust washer and thrust needle roller bearing.



29. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY


    D027993E03
  1. Hold the reverse clutch hub and turn the 1-way clutch assembly.

  1. check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.



30. REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY


    D027994E01
  1. Remove the 1-way clutch and No. 2 clutch drum thrust washer from the clutch drum and input shaft assembly.



31. FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    D027995E01
  1. Place the oil pump onto the torque converter, and then place the clutch drum and input shaft assembly onto the oil pump.



32. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY


    D027996E01
  1. Using a screwdriver, remove the snap ring.



    D027997E01
  1. Remove the reverse clutch hub sub-assembly, reverse clutch reaction sleeve, clutch cushion, plate reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum.



33. REMOVE REVERSE CLUTCH REACTION SLEEVE


    D027998E01
  1. Remove the reverse clutch reaction sleeve from the reverse clutch hub.



34. REMOVE REAR CLUTCH DISC


    D027999E09
  1. Remove the clutch cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.



35. INSPECT REAR CLUTCH DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



36. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY


    D028000E01
  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

    Standard inside diameter:
    35.812 to 35.837 mm (1.410 to 1.411 in.)

    Maximum inside diameter:
    35.887 mm (1.413 in.)

    1. If the inside diameter is greater than the maximum, replace the reverse clutch hub.



37. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


    D028001E01
  1. Remove the forward clutch hub from the clutch drum.



    D028500E03
  1. Remove the 2 thrust needle roller bearings from the forward clutch hub.



38. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY


    D028501E01
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

    Standard inside diameter:
    26.037 to 26.062 mm (1.025 to 1.026 in.)

    Maximum inside diameter:
    26.112 mm (1.028 in.)

    1. If the inside diameter is greater than the maximum, replace the forward clutch hub.



39. REMOVE MULTIPLE DISC CLUTCH HUB


    D028502E01
  1. Remove the multiple disc clutch hub from the clutch drum.



    D028503E05
  1. Remove the No. 2 thrust bearing race and input shaft thrust bearing race rear from the multiple disc clutch hub.



40. REMOVE INPUT SHAFT ASSEMBLY


    D028504E01
  1. Remove the thrust needle roller bearing from the clutch drum.



    D028505E01
  1. Remove the input shaft assembly from the clutch drum.



41. REMOVE INPUT SHAFT OIL SEAL RING


    D029677E01
  1. Remove the 3 oil seal rings from the input shaft.



42. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC


    D028519E01
  1. Using a screwdriver, remove the hole snap ring.



    C115806
  1. Remove the 2 flanges, 7 discs and 6 plates from the input shaft.



43. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



44. REMOVE NO. 1 CLUTCH BALANCER


    D028521E02
  1. Place SST on the clutch balancer, and compress the return spring with a press.

    SST
    09350-30020   (09350-07040, 09350-07070)

  1. Using a snap ring expander, remove the snap ring.



    D028522E01
  1. Remove the clutch balancer and forward clutch return spring from the input shaft assembly.



    D028523E01
  1. Remove the O-ring from the No. 1 clutch balancer.



45. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    26.74 mm (1.05 in.)



46. REMOVE FORWARD CLUTCH PISTON


    D028524E01
  1. While holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the input shaft to remove the forward clutch piston.



    D028525E01
  1. Remove the 2 O-rings from the forward clutch piston.



47. REMOVE REVERSE CLUTCH FLANGE


    D028506E01
  1. Remove the reverse clutch flange from the clutch drum.



48. REMOVE DIRECT CLUTCH DISC


    D028507E01
  1. Using a screwdriver, remove the 2 hole snap rings from the clutch drum.



    C162138
  1. Remove the reverse clutch flange, 6 discs and 6 plates from the clutch drum.



49. INSPECT DIRECT CLUTCH DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



50. REMOVE NO. 3 CLUTCH BALANCER


    D028509E04
  1. Place SST on the clutch balancer, and compress the return spring with a press.

    SST
    09387-00070  
    09350-30020   (09350-07070)



51. REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D028510E01
  1. Remove the reverse clutch return spring and O-ring from the reverse clutch piston.



52. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.04 mm (0.828 in.)



53. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY


    D028511E01
  1. Remove the reverse clutch piston sub-assembly from the clutch drum.



    D028512E01
  1. Remove the O-ring from the reverse clutch piston.



    D028513E01
  1. Remove the O-ring from the clutch drum.



54. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    D028514E06
  1. Place SST on the direct clutch piston, and compress the return spring with a press.

    SST
    09320-89010  
    09350-30020   (09350-07070)



    D028515E01
  1. Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.



    D028516E01
  1. Remove the O-ring from the clutch drum.



    D028517E01
  1. Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston.



    D028816E01
  1. Remove the 2 O-rings from the direct clutch piston.



55. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    C059838E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.51 mm (0.768 in.)



56. REMOVE NO. 3 BRAKE SNAP RING


    D027925E01
  1. Using a screwdriver, remove the No. 3 brake snap ring from the case.



57. REMOVE NO. 3 BRAKE DISC


    D027926E03
  1. Remove the flange, 4 discs, 4 plates and cushion plate from the case.



58. INSPECT NO. 3 BRAKE DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



59. REMOVE 2ND BRAKE PISTON HOLE SNAP RING


    D027927E03
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)



60. REMOVE 1-WAY CLUTCH ASSEMBLY


    D027928E01
  1. Remove the 1-way clutch assembly and No. 1 planetary carrier thrust washer from the case.



61. REMOVE 2ND BRAKE CYLINDER


    D027929E01
  1. Remove the 2nd brake cylinder from the case.



62. REMOVE 2ND BRAKE PISTON


    D028817E03
  1. Using SST and a press, compress the return spring and remove the snap ring.

    SST
    09351-40010  



    D028545E01
  1. Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.



    D028546E03
  1. Remove the 2 O-rings from the 2nd brake piston.



63. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D029828E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.72 mm (0.619 in.)



64. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D027930E01
  1. Remove the front planetary gear assembly and 1-way clutch inner race from the case.



    D027931E03
  1. Remove the thrust needle roller bearing, No. 3 thrust bearing race and No. 2 planetary carrier thrust washer from the front planetary gear assembly.



65. INSPECT FRONT PLANETARY GEAR ASSEMBLY


    D028544E01
  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    1. If the clearance is greater than the maximum, replace the front planetary gear assembly.



    D028543E01
  1. Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

    Maximum inside diameter:
    57.48 mm (2.26 in.)

    1. If the inside diameter is greater than the maximum, replace the front planetary gear.



66. INSPECT 1-WAY CLUTCH ASSEMBLY


D028542E03
  1. Install the 1-way clutch to the 1-way clutch inner race.

  1. Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

  1. Remove the 1-way clutch from the 1-way clutch inner race.



67. REMOVE FRONT PLANETARY RING GEAR


    D027932E01
  1. Remove the front planetary ring gear and bearing from the transmission case.



68. REMOVE CENTER PLANETARY RING GEAR


    D028540E01
  1. Using a screwdriver, remove the snap ring.



    D028541E01
  1. Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.



69. REMOVE NO. 1 BRAKE DISC


    C162132
  1. Remove the flange, 4 discs and 4 plates from the case.



70. INSPECT NO. 1 BRAKE DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



71. REMOVE BRAKE PISTON RETURN SPRING SNAP RING


    D027934E01
  1. Using a screwdriver, remove the brake piston return spring snap ring from the case.



72. REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D027935E01
  1. Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.



73. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D003830E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.05 mm (0.671 in.)



74. REMOVE NO. 1 BRAKE PISTON


    D027936E01
  1. Hold the No. 1 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the No. 1 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 1 brake piston.



75. REMOVE NO. 2 BRAKE DISC


    D027937E01
  1. Using a screwdriver, remove the snap ring from the case.



    D027938E03
  1. Remove the flange, 3 discs, 3 plates and brake piston return spring from the case.



76. INSPECT NO. 2 BRAKE DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



77. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D029829E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.45 mm (0.687 in.)



78. REMOVE NO. 2 BRAKE PISTON


    D027939E01
  1. Hold the No. 2 brake piston and apply compressed air (392 kPa, 4 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the 2 O-rings from the No. 2 brake piston.



79. REMOVE CENTER PLANETARY GEAR ASSEMBLY


    D027940E01
  1. Remove the No. 4 thrust bearing race, center planetary gear and planetary sun gear from the case.



80. INSPECT CENTER PLANETARY GEAR ASSEMBLY


D028533E01
  1. Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

    Standard clearance:
    0.12 to 0.68 mm (0.00472 to 0.0268 in.)

    Maximum clearance:
    0.73 mm (0.0287 in.)

    1. If the clearance is greater than the maximum, replace the center planetary gear assembly.



81. REMOVE INTERMEDIATE SHAFT


    D027941E01
  1. Using a screwdriver, remove the snap ring from the case.



    D027942E01
  1. Remove the intermediate shaft with No. 3 1-way clutch assembly from the case.



82. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY


    D028532E03
  1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



83. REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY


    D027964E01
  1. Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.



84. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    D027965E05
  1. Remove the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and planetary ring gear flange from the intermediate shaft.



85. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


D028531E01
  1. Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.

    Maximum inside diameter:
    32.175 mm (1.27 in.)

    1. If the inside diameter is greater than the maximum, replace the rear planetary ring gear.



86. INSPECT INTERMEDIATE SHAFT


    D028529E04
  1. Using a dial indicator, measure the intermediate shaft runout.

    Maximum runout:
    0.08 mm (0.00315 in.)

    If the runout is greater than the maximum, replace the intermediate shaft with a new one.



    D028530E02
  1. Using a micrometer, measure the outer diameter of the intermediate shaft positions shown in the diagram.

    Standard diameter:
    A, B:
    25.962 to 25.975 mm (1.022 to 1.023 in.)
    C, D:
    32.062 to 32.075 mm (1.262 to 1.263 in.)

    Minimum diameter:
    A, B:
    25.912 mm (1.02 in.)
    C, D:
    32.012 mm (1.26 in.)

    If the outer diameter is less than the minimum, replace the intermediate shaft with the new one.



87. REMOVE BRAKE PLATE STOPPER SPRING


D027943E01


88. REMOVE NO. 4 BRAKE DISC


    D027944E03
  1. Remove the 7 plates, 8 discs and 2 flanges from the case.



89. INSPECT NO. 4 BRAKE DISC


    D001216E01
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.



90. REMOVE REAR PLANETARY GEAR ASSEMBLY


    D027945E01
  1. Remove the rear planetary gear assembly from the case.



    D027946E03
  1. Remove the No. 9 thrust bearing race and the thrust needle roller bearing from the rear planetary gear.



    D027947E01
  1. Remove the thrust needle roller bearing from the case.



91. INSPECT REAR PLANETARY GEAR ASSEMBLY


    D028527E01
  1. Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    1. If the clearance is greater than the maximum, replace the planetary gear assembly.



    D028528E01
  1. Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

    Maximum inside diameter:
    20.075 mm (0.790 in.)

    1. If the inside diameter is greater than the maximum, replace the rear planetary gear assembly.



92. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D028083E02
  1. Place SST on the spring retainer and compress the brake return spring.

    SST
    09350-30020   (09350-07050)

  1. Using SST, remove the snap ring and brake return spring.

    SST
    09350-30020   (09350-07070)



93. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D029830E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    23.74 mm (0.935 in.)



94. REMOVE 1ST AND REVERSE BRAKE PISTON


    D027948E01
  1. Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the 1st and reverse brake piston.



95. REMOVE BRAKE REACTION SLEEVE


    D028079E04
  1. Using SST, remove the reaction sleeve.

    SST
    09350-30020   (09350-07080)

  1. Remove the O-ring from the reaction sleeve.



96. REMOVE NO. 4 BRAKE PISTON


    D001240E03
  1. Using SST, remove the brake piston.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the brake piston.