Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2440    Secondary Air Injection System Switching Valve Stuck Open Bank1

DTC    P2441    Secondary Air Injection System Switching Valve Stuck Close Bank1

DTC    P2442    Secondary Air Injection System Switching Valve Stuck Open Bank 2

DTC    P2443    Secondary Air Injection System Switching Valve Stuck Closed Bank 2

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC Code
DTC Detection Condition
Trouble Area
P2440
P2442
Pressure sensor detects pulsation of exhaust gas despite ECM commanding Air Switching Valve (ASV) to close, while engine running
(1 trip detection logic)
  1. ASV
  2. Open or short in ASV circuit
  3. Pressure sensor
  4. Pressure sensor circuit
  5. Air Injection Control Driver (AID)
  6. ECM
P2441
P2443
Pressure sensor detects no pulsation of exhaust gas despite ECM commanding Air Switching Valve (ASV) to open, while engine running
(2 trip detection logic)
  1. ASV
  2. Open or short in ASV circuit
  3. Vacuum hose (ASV - pressure sensor)
  4. Air injection hose
  5. Pressure sensor
  6. Pressure sensor circuit
  7. Air Injection Control Driver (AID)
  8. ECM

HINT:
Air switching valve normal operation:
When the Air Switching Valve (ASV) is open, exhaust gas pulsation occurs in the secondary air passage.
When the ASV is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor connected to the ASV of the Secondary Air Injection (AIR) system.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and sets a DTC:
  1. Exhaust gas pulsation is detected by the pressure sensor despite the ECM commanding the ASV to close.
  2. Exhaust gas pulsation is not detected by the pressure sensor despite the ECM commanding the ASV to open.

MONITOR STRATEGY


Related DTCs
P2440: Air control valve stuck open
P2441: Air control valve stuck closed
P2442: Air control valve stuck open
P2443: Air control valve stuck closed
Required Sensors/Components (Main)
Pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per drive cycle
Duration
2 seconds: Case 3
7 seconds: Case 1, 2
MIL Operation
1 driving cycle: Case 3
2 driving cycles: Case 1, 2
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air fuel ratio sensor Heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348, P1340 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0451, P0452, P0453, P1451, P1452 P1453, P1455 (EVAP system)
P0500 (Vehicle speed sensor)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Front oxygen/Air fuel ratio sensor)
P2431 - P2438 (Secondary air injection system pressure sensor)
Battery voltage
11 V or more
Atmospheric pressure
45 kPa (337.5 mmHg) or more

Case 1: 
Secondary air injection pump
ON
Secondary air injection switching valve
ON
Engine speed
Less than 3750 rpm

Case 2: 
Secondary air injection pump
OFF
Engine speed
Less than 3750 rpm
Secondary air injection system monitor during secondary air injection ON
Completed

Case 3: 
Cumulative intake air amount
100 g/sec. or more
Engine speed
Less than 3750 rpm
AIR pump
OFF
AIR valve
OFF
AIR status
OFF

TYPICAL MALFUNCTION THRESHOLDS


Condition 1: 
AIR pressure during AIR ON
2.4 kPa or more and pulse is generated

Condition 2: 
AIR pressure during AIR ON
Less than 2.4 kPa and pulse is generated

Condition 3: 
AIR pressure during AIR ON
2.4 kPa or more and pulse is not generated

Condition 4: 
AIR pressure during AIR ON
Less than 2.4 kPa and pulse is not generated

Condition 5: 
AIR pressure during AIR OFF
2.4 kPa or more and pulse is generated

Condition 6: 
AIR pressure during AIR OFF
Less than 2.4 kPa and pulse is generated

Condition 7: 
AIR pressure during AIR OFF
2.4 kPa or more and pulse is not generated

Condition 8: 
AIR pressure during AIR OFF
Less than 2.4 kPa and pulse is not generated

Case 1: 
Any of following conditions met:
(a), (b) or (c)
(a) Conditions 1 and 6
Met
(b) Conditions 1 and 5
Met
(c) Conditions 2 and 6
Met

Case 2: 
Any of following conditions met:
(a), (b) or (c)
(a) Conditions 3 and 7
Met
(b) Conditions 3 and 8
Met
(c) Conditions 4 and 8
Met

Case 3: 
Cumulative pressure pulsation
60 kPa or more

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and sets a DTC. Soon after cold engine starts, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1: 
Air Pump
ON
Air Switching Valve
Open
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2: 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3: 
Air Pump
ON
Air Switching Valve
Closed
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4: 
Air Pump
OFF
Air Switching Valve
Close
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5: 
Air Pump
ON
Air Switching Valve
Open
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6: 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7: 
Air Pump
ON
Air Switching Valve
Closed
Pressure
2.4 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8: 
Air Pump
OFF
Air Switching Valve
Close
Pressure
Less than 2.4 kPa
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

HINT:
  1. In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 20 to 30 kPa).
  2. In case 1, the average pressure is approximately 3 to 11 kPa. The value of 2.4 kPa indicated in the table above is a threshold for detecting pump malfunctions.


Detected Conditions while AIR operating:
Air pump ON, ASV Open
Detected Conditions while AIR not operating:
Air pump OFF, ASV Closed
ECM Determination
DTCs Output
Case 1
Case 8
Normal
-
Case 1
Case 6
ASV stuck open
P2440
or
P2442
Case 1
Case 7
Air pump stuck ON
P2444
or
P2446
Case 2
Case 8
Air pump stuck OFF
P2445
or
P2447
Case 3
Case 8
ASV stuck closed
P2441
or
P2443
Case 1
Case 5
ASV stuck open and air pump stuck ON
P2440 and P2444
or
P2442 and P2446
Case 2
Case 6
ASV stuck open and air pump stuck OFF
P2440 and P2445
or
P2442 and P2447
Case 3
Case 7
ASV stuck closed and air pump stuck ON
P2441 and P2444
or
P2443 and P2446
Case 4
Case 8
ASV stuck closed and air pump stuck OFF
P2441 and P2445
or
P2443 and P2447

HINT:
  1. If the vacuum hose between the ASV and the pressure sensor is not connected correctly, case 4 may occur.
  2. By using the Techstream to perform the Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Air Injection Check / Automatic Mode after the repair.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:
  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON and turn the Techstream ON.
    5. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    6. Start the engine.
    7. Perform the AIR system intrusive operation while the engine is idling.
    8. Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

      Standard:

      Operation
      AIR PUMP
      ASV
      PRESSURE*1
      PULSATION*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      2.4 kPa or more
      20 kPa or more
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Less than 2.4 kPa
      Less than 30 kPa

      *1:
      Average pumping pressure (gauge pressure). The pressure should be 2.4 kPa or more when the AIR system operates.
      *2:
      The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
    9. Turn the ignition switch to OFF.

      NOTICE:
      1. This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
        Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Air Injection Check operation finishes.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2440, P2441, P2442 and/or P2443 are output
    A
    P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output
    B
    P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output
    C

If any DTCs other than P0412, P0415, P2440, P2441, P2442 and/or P2443 are output, troubleshoot those DTCs first.


B
GO TO AIR SWITCHING VALVE INSPECTION PROCEDURE (P0412 AND P0415)

C
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM
A165754E01
  1. Visual check

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Disconnect the No. 1 air hose.

    4. Connect the Techstream to the DLC3.

    5. Turn the ignition switch to ON and turn the Techstream ON.

    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AP and ASV operation can be selected.

    7. Start the engine.

    8. Perform the AIR system intrusive operation while the engine is idling.

    9. Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.

      CAUTION:
      To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.

    11. Check that the exhaust gas does not pulsate when the ASV is turned OFF.

    12. Turn the ignition switch off.

      NOTICE:
      1. This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Air Injection Check operation finishes.

      Standard:
      Air Pump Operations
      ASV Operations
      Exhaust Gas Pulsation
      ON
      OFF
      Not detected
      ON
      ON
      Detected

  1. Other inspection method:
    The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.
    Perform System Check operation under Manual Mode.
    *: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Connect the Techstream to the DLC3.

    4. Turn the ignition switch to ON and turn the Techstream ON.

    5. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

    6. Start the engine after the Techstream initialization is finished.

    7. Perform the AIR system intrusive operation while the engine is idling.

    8. Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream indicate the conditions shown in the table below.

    9. Turn the ignition switch off.


OK:

AIR System Operation
Pulsation Condition
(ECM Calculation)
Air-Fuel Ratio
(Reference)
AIR PUMP: ON, ASV: OPEN
20 kPa or more
18 or more
AIR PUMP: OFF, ASV: CLOSE
Less than 30 kPa
Approximately 14.5
(around stoichiometric air-fuel ratio)

Reference:
If the air pump operation is confirmed as normal (Click here), the air-fuel ratio detected in front of three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.
Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 9
A


3.INSPECT AIR TUBE (BLOCKAGES AND LEAKAGES)
A165755E01
  1. Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the ASV.

  1. Inspect the air tube for blockages and damage.

    OK:
    No blockages and damage on intake pipe.



NG
REPLACE AIR TUBE (Click here)
OK


4.INSPECT AIR SWITCHING VALVE
  1. Inspect the air switching valve .



NG
REPLACE AIR SWITCHING VALVE (Click here)
OK


5.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
A162305E01
  1. Disconnect the D48 and D50 or D52 and D54 AID connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D48-1 (BATT) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D50-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D52-1 (BAT2) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D54-5 (+B2) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D50-1 (E) - Body ground
    Always
    Below 1 Ω
    D54-1 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


6.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
A164736E01
  1. Disconnect the A24 or D74 ECM connector.

  1. Disconnect the D50 or D54 AID connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D74-28 (AIRV) - D50-3 (SIV)
    Always
    Below 1 Ω
    A24-43 (ARV2) - D54-3 (SIV2)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Clear DTCs (if set) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END 

9.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - PRESSURE SENSOR)

OK:
No blockage and no deformation in vacuum hose.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


10.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)
A165753E01
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute) and Air Pump2 Pressure (Absolute).

  1. Check that the pressure displayed on the Techstream fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    NOTICE:
    Do not let foreign matter enter the sensor when applying pressure.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.



NG
REPLACE AIR SWITCHING VALVE (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)