Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with mineral oil will result in the loss of the skin's natural oils, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
  3. In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



1. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 5 bolts, 3 screws and engine under cover.



2. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



3. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Remove the drain pipe cap.



    A134828E02
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    1. Put the disposal container beneath the drain hose to collect the oil from the oil filter cover.
    2. Drain hose inside diameter: 8 mm (0.315 in.)
    3. Drain hose length: 900 mm (2.95 ft.)



4. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.



    A134830E02
  1. Using SST, tighten the oil filter. Depending on the work space available, choose from the following.

    SST
    09228-07501  

    1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or with a common wrench.



5. ADD ENGINE OIL
  1. Remove the oil filler cap.

  1. Add new oil.

    Standard oil grade:

    Oil grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    5W-30
    (5W-30 is the best choice for good fuel economy and good starting in cold weather.)

    HINT:
    If SAE 5W-30 is not available, use SAE 10W-30.


    Standard oil capacity:

    Item
    Specified Condition
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 Imp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 Imp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 Imp. qts)

  1. Install the oil filler cap.



6. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



7. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine so that the coolant temperature is approximately 80°C (176°F). Check the engine oil level dipstick 5 minutes after the engine is stopped. Then add engine oil to the full level of the engine oil level dipstick.



8. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the engine under cover with the 5 bolts and 3 screws.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }