Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-FE, 3UR-FBE)

DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-FE, 3UR-FBE) > DISASSEMBLY

for Preparation Click here



1. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    F001237E09
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Standard Condition
    Vertical runout
    0.1 mm (0.00394 in.)
    Lateral runout
    0.1 mm (0.00394 in.)

    If the runout is greater than the maximum, replace the companion flange.



2. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


    C161428
  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.05 mm (0.00197 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



3. INSPECT DIFFERENTIAL RING GEAR BACKLASH


    C161429
  1. Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00788 in.)

    HINT:
    Measure at 3 or more positions around the circumference of the ring gear.

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



4. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH


    C159766
  1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the case.

    Standard backlash:
    0.15 mm (0.00591 in.) or less

    If the backlash is not within the specification, replace the side gear thrust washer with one of a different thickness.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C124126
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard drive pinion preload (at starting):
    1.62 to 2.25 N*m (17 to 22 kgf*cm, 15 to 19 in.*lbf)

    If necessary, disassemble and inspect the differential.



6. INSPECT TOTAL PRELOAD


    C124126
  1. Using a torque wrench, measure the total preload with the teeth of the drive pinion and ring gear in contact.

    Standard total preload (at starting):
    Standard drive pinion preload plus 0.19 to 0.38 N*m (2 to 3 kgf*cm, 2 to 3 in.*lbf)

    If necessary, disassemble and inspect the differential.



7. REMOVE REAR DRIVE PINION NUT


    F044346E01
  1. Using SST and a hammer, unstake the nut.

    SST
    09930-00010  



    C124130E01
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)



8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C186905E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03030)
    09955-03050  



9. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    C162373E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  



10. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


11. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C186906E01
  1. Using SST, remove the bearing (inner race).

    SST
    09950-40011   (09951-04010, 09953-04020, 09952-04010)
    09955-04130  
    09958-04020  

  1. Remove the 2 preload adjusting shims.



12. REMOVE REAR DIFFERENTIAL CASE ASSEMBLY


    C161430E01
  1. Place matchmarks on the bearing cap and differential carrier.

  1. Remove the 4 bolts and 2 differential bearing caps.



    C124135E02
  1. Using SST and a plastic-faced hammer, remove the 2 side bearing plate washers.

    SST
    09504-22011  

    HINT:
    Measure the plate washer thickness and note it down.

  1. Remove the differential case with the bearing outer races from the carrier.

    HINT:
    Tag the bearing outer races to show the location for reassembling.



13. REMOVE REAR DIFFERENTIAL DRIVE PINION


    C030540
  1. Remove the differential drive pinion and bearing spacer from the differential carrier.



14. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C116049E01
  1. Using SST and a press, press out the bearing (inner race).

    SST
    09950-00020  
    If either the drive pinion or ring gear is damaged, replace them as a set.



15. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


16. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C186907E01
  1. Using SST, remove the bearing (outer race).

    SST
    09308-00010  
    If the bearing is damaged during removal, replace it.



17. REMOVE DIFFERENTIAL OIL STORAGE RING


    C161484
  1. Using a brass bar and hammer, tap out the storage ring.



18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C161485
  1. Using a brass bar and hammer, tap out the bearing (outer race).
    If the bearing is damaged during removal, replace it.



19. REMOVE DIFFERENTIAL RING GEAR


    C159770E01
  1. Place matchmarks on the ring gear and differential case.

  1. Remove the 12 ring gear set bolts.

  1. Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.



20. INSPECT REAR DIFFERENTIAL CASE ASSEMBLY RUNOUT

HINT:
C066468
If the ring gear runout is within the specification (see "INSPECT RUNOUT OF DIFFERENTIAL RING GEAR" procedure), this inspection is not necessary.

  1. Install the differential case to the differential carrier.

  1. Inspect the differential case runout.

    Maximum runout:
    0.04 mm (0.00158 in.)

  1. Remove the differential case from the differential carrier.



21. REMOVE REAR DIFFERENTIAL CASE BEARING


    C186908E01
  1. Using SST, remove the 2 bearings.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
    09950-60010   (09951-00500)
    09955-04120  

    HINT:
    Fix the claws of SST to the notches in the differential case.



22. DISASSEMBLE DIFFERENTIAL CASE


    C159772
  1. Using a pin punch and hammer, tap out the straight pin.

  1. Remove the pinion shaft, 2 pinion gears, 2 pinion gear thrust washers, 2 side gears and 2 side gear thrust washers.



23. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


    C116055E02
  1. When replacing dust reflector:
    Using SST, a steel plate and press, press out the dust deflector.

    SST
    09950-00020  

    NOTICE:
    Do not drop the companion flange.



24. REMOVE REAR DIFFERENTIAL DYNAMIC DAMPER (for Regular Cab Standard Deck)


    C160325
  1. Remove the bolt, washer and dynamic damper.