Home › BRAKE › PARKING BRAKE › PARKING BRAKE ASSEMBLY

PARKING BRAKE ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL PARKING BRAKE ANCHOR BLOCK


    C155126
  1. Install the anchor block with the 2 nuts.

    Torque:
    86 N*m{ 877 kgf*cm , 63 ft.*lbf }



2. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C154244
  1. Connect the No. 3 parking brake cable with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL PARKING BRAKE SHOE LEVER LH
  1. Apply high temperature grease to the parking brake shoe lever.



    C155125
    C117760E02
  1. Install the parking brake shoe lever to the No. 3 parking brake cable.

    NOTICE:
    Carefully distinguish the parking brake shoe lever RH and LH.



4. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH
  1. Apply high temperature grease to the areas of the backing plate that contact the shoe.



    C154249E01
  1. Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

    SST
    09718-00011  



5. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH
  1. Apply high temperature grease to the areas of the backing plate that contact the shoe.



    C193371E01
  1. Apply the high temperature grease to the areas of the shoe adjusting screw set shown in the illustration.

  1. Set the parking brake shoe and shoe adjuster screw set in place.

  1. Connect the tension spring.



    C155124E01
  1. Using SST, install the No. 1 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

    SST
    09718-00011  



6. INSTALL PARKING BRAKE SHOE RETURN SPRING


    C179358E01
  1. Using SST, install the shoe return spring.

    SST
    09703-30011  



7. CHECK PARKING BRAKE INSTALLATION


  1. Check that each part is installed properly.


    C156989E01



8. INSTALL REAR DISC


    C155452E01
  1. Align the matchmarks and install the rear disc.



9. ADJUST PARKING BRAKE SHOE CLEARANCE
  1. Temporarily install the hub nuts.

  1. Remove the hole plug.



    C158874E01
  1. Insert an adjustment tool into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.

  1. Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.

  1. Install the hole plug.

  1. Remove the hub nuts.



10. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH


    C158344
  1. Connect the rear disc brake cylinder with 2 new bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    1. Do not twist the brake hose.
    2. Make sure that the bolts are free from damage and foreign matter.
    3. Do not overtighten the bolts.



11. INSTALL REAR WHEEL LH

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }



12. SETTLE PARKING BRAKE SHOE AND DISC
  1. Drive the vehicle for approximately 400 m (0.25 miles) under the following conditions.

    1. The vehicle speed is approximately 50 km/h (31 mph) and the vehicle is on a safe, level and dry road.

    2. The parking brake pedal is being depressed with a force of 150 N (15 kgf, 33.7 lbf).

  1. Repeat the procedures above 2 or 3 times.



13. CHECK PARKING BRAKE PEDAL TRAVEL
  1. Firmly depress the parking brake pedal.

  1. Release the parking brake.

  1. Slowly depress the parking brake pedal with a force of approximately 300 N (31 kgf, 67.4 lbf) and count the number of clicks.

    OK:
    6 to 9 clicks



14. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Depress the parking brake pedal.



    C159467E01
  1. Apply load equivalent to 4 kN (408 kgf, 899.2 lbf) on equalizer twice to pull No. 2 and No. 3 parking brake cable to remove initial elongation.

  1. Release the parking brake pedal to the original position.



    C154230
  1. Loosen the pedal side No. 1 parking brake cable lock nut.

  1. Turn the pedal side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

    Standard parking brake pedal travel:
    Pedal Load
    Click Number
    300 N (31 kgf, 67.4 lbf)
    6 to 9

  1. Using a wrench or equivalent to hold the adjustment nut, tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Pay attention that the adjustment nut does not rotate with the lock nut during tightening.



  1. Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable underbody side as follows.

    1. Release the parking brake pedal to the original position.



    2. C159467E02
    3. Loosen the underbody side No. 1 parking brake cable lock nut.

    4. Turn the underbody side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

      Standard parking brake pedal travel:
      Pedal Load
      Click Number
      300 N (31 kgf, 67.4 lbf)
      6 to 9

    5. Tighten the No. 1 parking brake cable underbody lock nut.

      Torque:
      13 N*m{ 128 kgf*cm , 9 ft.*lbf }

      NOTICE:
      Pay attention that the adjustment nut does not rotate with the lock nut during tightening.

  1. Depress and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.

    OK:
    6 to 9 clicks

    If the result is not as specified, adjust the parking brake pedal travel again.

  1. Check whether the parking brake drags or not.
    If the parking brake drags, adjust the shoe clearance.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on at the first notch.
    If not, adjust the parking brake switch installation position.