Home › BRAKE › BRAKE › FRONT BRAKE FLEXIBLE HOSE

FRONT BRAKE FLEXIBLE HOSE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT FLEXIBLE HOSE


    C154488E03
  1. Attach the 2 clips (labeled A) to the flexible hose.

  1. Using a union nut wrench (10 mm), connect the flexible hose to the brake tube and wheel cylinder tube while holding the flexible hose with a wrench.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.

    NOTICE:
    1. Do not bend or damage the brake tube and wheel cylinder tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake tube and wheel cylinder tube from the connecting points.



2. FILL RESERVOIR WITH BRAKE FLUID


    C155472
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    NOTICE:
    1. Make sure there is sufficient brake fluid in the can.
    2. After adding brake fluid, make sure the reservoir is sufficiently full.



3. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.



    C155473E02
  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.

  1. Slowly depress and hold the brake pedal.



    C155474
  1. Block the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.



4. BLEED AIR FROM BRAKE LINE



C155475E01

  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



5. BLEED AIR FROM VSC ACTUATOR ASSEMBLY

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the Techstream to the DLC3, and turn the ignition switch ON.

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.

  1. Bleed the air out of the suction line.

    NOTICE:
    1. Perform the bleeding at the right front wheel and right rear wheel.
    2. Bleed the air by following the steps displayed on the Techstream.


    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.

    2. Loosen the bleeder plug.

    3. Operate the brake actuator to bleed the air using the Techstream.

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    4. Check if the operation has stopped by referring to the Techstream display.

    5. Temporarily tighten the bleeder plug.

    6. Repeat the 4 previous steps until all air in the fluid is completely bled out.

    7. Tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    8. Repeat all of the above procedures for the other wheel to bleed the air out of the suction line.

  1. Bleed the air out of the pressure reduction line.

    NOTICE:
    1. Perform the bleeding at the 4 wheels.
    2. Bleed the air by following the steps displayed on the Techstream.


    1. Connect a vinyl tube to one of the bleeder plugs.

    2. Loosen the bleeder plug.

    3. Using the Techstream operate the brake actuator, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Depress and hold the brake pedal. Do not depress and release the pedal repeatedly.

      HINT:
      The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.

    4. Tighten the bleeder plug, then release the brake pedal.

    5. Repeat the 3 previous steps until all air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    7. Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.



6. CHECK BRAKE FLUID LEVEL IN RESERVOIR


C155477
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



7. INSPECT FOR BRAKE FLUID LEAK


8. INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }