Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2796    No Communication in Immobiliser System

DTC    B2798    Communication Malfunction No. 2

for Preparation Click here


DESCRIPTION

  1. DTC B2796 is output when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU.
  2. DTC B2798 is output when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU.

DTC Code
DTC Detection Condition
Trouble Area
B2796
The key code cannot be transmitted
  1. Key
  2. Harness or connector
  3. Transponder key ECU
  4. Transponder key amplifier
B2798
Key code identification cannot be completed within the specified time
Key

WIRING DIAGRAM


B121682E15


INSPECTION PROCEDURE

HINT:
When the transponder key ECU is replaced, reregister the ECU - ECM communication ID .

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTC (Click here).

    OK:
    DTC B2796 or B2798 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.READ VALUE USING TECHSTREAM (ENGINE IMMOBILISER SYSTEM)
  1. Use the Data List to check if the engine immobiliser system is functioning properly.

    OK:
    Unset (key is in ignition key cylinder) appears on the screen.


    Immobiliser 
    Tester Display
    Measurement Item / Display
    Normal Condition
    Diagnostic Note
    Immobiliser
    Immobiliser system status / Set or Unset
    Set: No key is in ignition key cylinder
    Unset: Key is in ignition key cylinder
    -



NG
Go to step 4
OK

REPLACE TRANSPONDER KEY ECU (Click here)  

4.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
  1. Check if the engine starts with an already registered vehicle key.

    OK:
    Engine starts.



NG
Go to step 5
OK

REREGISTER KEY CODE OR REPLACE KEY THAT CANNOT START ENGINE 

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
B110403E33
  1. Disconnect the J26 ECU connector.

  1. Disconnect the J20 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J26-14 (VC5) - J20-1 (VC5)
    Always
    Below 1 Ω
    J26-15 (CODE) - J20-4 (CODE)
    J26-4 (TXCT) - J20-5 (TXCT)
    J26-5 (AGND) - J20-7 (AGND)
    J26-14 (VC5) or J20-1 (VC5) - Body ground
    Always
    10 kΩ or higher
    J26-15 (CODE) or J20-4 (CODE) - Body ground
    J26-4 (TXCT) or J20-5 (TXCT) - Body ground
    J26-5 (AGND) or J20-7 (AGND) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE TRANSPONDER KEY AMPLIFIER
  1. Temporarily replace the transponder key amplifier with a new or normally functioning one (Click here).


NEXT


7.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts normally.

    OK:
    Engine starts normally.



NG
REPLACE TRANSPONDER KEY ECU (Click here)
OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)