Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for CrewMax)

AUDIO AND VISUAL SYSTEM (for CrewMax) > Speaker Circuit (Independent Amplifier)

for Preparation Click here


DESCRIPTION

The stereo component amplifier sends sound signals to the speaker.

WIRING DIAGRAM


E146449E01


E149216E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result: 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 11
A


2.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result: 
    Result
    Proceed to
    Front No. 1 speaker
    A
    Front No. 2 speaker
    B
    Front No. 3 speaker
    C
    Front No. 4 speaker
    D



B
Go to step 5

C
Go to step 7

D
Go to step 9
A


3.INSPECT FRONT NO. 1 SPEAKER


    E144966E01
  1. Disconnect the M8 and N10 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER
OK


4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1 SPEAKER)


    E146498E01
  1. Disconnect the M8 and N10 speaker connectors.

  1. Disconnect the K17 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K17-2 (WFL+) - N10-1
    Always
    Below 1 Ω
    K17-1 (WFL-) - N10-2
    K17-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    K17-1 (WFL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K17-9 (WFR+) - M8-1
    Always
    Below 1 Ω
    K17-3 (WFR-) - M8-2
    K17-9 (WFR+) - Body ground
    Always
    10 kΩ or higher
    K17-3 (WFR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER  

5.INSPECT FRONT NO. 2 SPEAKER


    E144969E09
  1. Disconnect the K10 and K12 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    3 (TWL+) - 4 (TWL-)
    Always
    1.3 to 2.3 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    3 (TWR+) - 4 (TWR-)
    Always
    1.3 to 2.3 Ω



NG
REPLACE FRONT NO. 2 SPEAKER
OK


6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2 SPEAKER)


    E146508E01
  1. Disconnect the K16 amplifier connector.

  1. Disconnect the K10 and K12 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K16-8 (FL+) - K12-3 (TWL+)
    Always
    Below 1 Ω
    K16-7 (FL-) - K12-4 (TWL-)
    K16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    K16-7 (FL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K16-2 (FR+) - K10-3 (TWR+)
    Always
    Below 1 Ω
    K16-6 (FR-) - K10-4 (TWR-)
    K16-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    K16-6 (FR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER  

7.INSPECT FRONT NO. 3 SPEAKER


    E160614E13
  1. Disconnect the M1 and N1 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER
OK


8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)


    E146500E01
  1. Disconnect the M1, N1, K10 and K12 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K12-1 (+) - N1-3
    Always
    Below 1 Ω
    K12-2 (-) - N1-1
    K12-1 (+) - Body ground
    Always
    10 kΩ or higher
    K12-2 (-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K10-1 (+) - M1-3
    Always
    Below 1 Ω
    K10-2 (-) - M1-1
    K10-1 (+) - Body ground
    Always
    10 kΩ or higher
    K10-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER (Click here)  

9.INSPECT FRONT NO. 4 SPEAKER


    E146506E01
  1. Disconnect the K14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER
OK


10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 4 SPEAKER)


    E146501E01
  1. Disconnect the K14 speaker connector.

  1. Disconnect the K17 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-4 (CTR+) - K14-1
    Always
    Below 1 Ω
    K17-10 (CTR-) - K14-2
    K17-4 (CTR+) - Body ground
    Always
    10 kΩ or higher
    K17-10 (CTR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER  

11.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result: 
    Result
    Proceed to
    Rear No. 2 speaker
    A
    Rear No. 1 speaker
    B
    Box speaker
    C



B
Go to step 14

C
Go to step 16
A


12.INSPECT REAR NO. 2 SPEAKER


    E160614E15
  1. Disconnect the O2 and O8 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    2.5 to 3.5 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER
OK


13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - REAR NO. 2 SPEAKER)


    E149221E01
  1. Disconnect the K16 amplifier connector.

  1. Disconnect the O2 and O8 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K16-3 (RL+) - O8-3 (+TW)
    Always
    Below 1 Ω
    K16-9 (RL-) - O8-1 (-TW)
    K16-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    K16-9 (RL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K16-10 (RR+) - O2-3 (+TW)
    Always
    Below 1 Ω
    K16-4 (RR-) - O2-1 (-TW)
    K16-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    K16-4 (RR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER  

14.INSPECT REAR NO. 1 SPEAKER


    E144966E02
  1. Disconnect the O1 and O7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE REAR NO. 1 SPEAKER
OK


15.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SPEAKER - REAR NO. 2 SPEAKER)


    E149222E01
  1. Disconnect the O1, O2, O7 and O8 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    O8-4 (+) - O7-1
    Always
    Below 1 Ω
    O8-2 (-) - O7-2
    O8-4 (+) - Body ground
    Always
    10 kΩ or higher
    O8-2 (-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    O2-4 (+) - O1-1
    Always
    Below 1 Ω
    O2-2 (-) - O1-2
    O2-4 (+) - Body ground
    Always
    10 kΩ or higher
    O2-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR NO. 2 SPEAKER  

16.INSPECT BOX SPEAKER


    E144969E02
  1. Disconnect the P14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE BOX SPEAKER
OK


17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - BOX SPEAKER)


    E146502E01
  1. Disconnect the K17 amplifier connector.

  1. Disconnect the P14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-5 (WF1+) - P14-1
    Always
    Below 1 Ω
    K17-12 (WF1-) - P14-2
    K17-5 (WF1+) - Body ground
    Always
    10 kΩ or higher
    K17-12 (WF1-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER