Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab)

DTC    74-40    Short in Speaker Circuit

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
74-40
A short is detected in the speaker output circuit.
  1. Wire harness
  2. Speaker
  3. Stereo component amplifier

WIRING DIAGRAM


E146449E01


E146450E01


INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.

1.CHECK DTC
  1. Disconnect the K16 and K17 amplifier connectors.

  1. Clear the DTC.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER
OK


2.CHECK DTC
  1. Reconnect the K16 amplifier connector.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)


    E147602E01
  1. Disconnect the K17 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    K17-1 (WFL-) - Body ground
    K17-9 (WFR+) - Body ground
    K17-3 (WFR-) - Body ground
    K17-4 (CTR+) - Body ground
    K17-10 (CTR-) - Body ground
    K17-5 (WF1+) - Body ground
    K17-12 (WF1-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 1 SPEAKER LH


    E144966E04
  1. Disconnect the N10 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER LH
OK


5.INSPECT FRONT NO. 1 SPEAKER RH


    E144966E05
  1. Disconnect the M8 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER RH
OK


6.INSPECT FRONT NO. 4 SPEAKER


    E146506E01
  1. Disconnect the K14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER
OK

REPLACE BOX SPEAKER  

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)


    E147603E01
  1. Disconnect the K16 amplifier connector.

  1. Disconnect the K10 and K12 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    K16-7 (FL-) - Body ground
    K16-2 (FR+) - Body ground
    K16-6 (FR-) - Body ground
    K16-3 (RL+) - Body ground
    K16-9 (RL-) - Body ground
    K16-10 (RR+) - Body ground
    K16-4 (RR-) - Body ground
    K10-1 (+) - Body ground
    K10-2 (-) - Body ground
    K12-1 (+) - Body ground
    K12-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 3 SPEAKER LH


    E160614E11
  1. Disconnect the N1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER LH
OK


9.INSPECT FRONT NO. 3 SPEAKER RH


    E160614E12
  1. Disconnect the M1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER RH
OK


10.INSPECT FRONT NO. 2 SPEAKER LH


    E144969E06
  1. Disconnect the K12 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWL+) - 4 (TWL-)
    Always
    1.3 to 2.3 Ω
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)



NG
REPLACE FRONT NO. 2 SPEAKER LH
OK


11.INSPECT FRONT NO. 2 SPEAKER RH


    E144969E07
  1. Disconnect the K10 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWR+) - 4 (TWR-)
    Always
    1.3 to 2.3 Ω
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)



NG
REPLACE FRONT NO. 2 SPEAKER RH
OK


12.INSPECT REAR NO. 1 SPEAKER LH


    E144966E06
  1. Disconnect the O7 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE REAR NO. 1 SPEAKER LH
OK

REPLACE REAR NO. 1 SPEAKER RH