Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for CrewMax)

DTC    74-40    Short in Speaker Circuit

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
74-40
A short is detected in the speaker output circuit.
  1. Harness and connector
  2. Speaker
  3. Stereo component amplifier

WIRING DIAGRAM


E146449E01


E149216E01


INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.

1.CHECK DTC
  1. Disconnect the K16 and K17 amplifier connectors.

  1. Clear the DTC.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER
OK


2.CHECK DTC
  1. Reconnect the K16 amplifier connector.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)


    E147602E01
  1. Disconnect the K17 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    K17-1 (WFL-) - Body ground
    K17-9 (WFR+) - Body ground
    K17-3 (WFR-) - Body ground
    K17-4 (CTR+) - Body ground
    K17-10 (CTR-) - Body ground
    K17-5 (WF1+) - Body ground
    K17-12 (WF1-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 1 SPEAKER LH


    E144966E04
  1. Disconnect the N10 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER LH
OK


5.INSPECT FRONT NO. 1 SPEAKER RH


    E144966E05
  1. Disconnect the M8 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER RH
OK


6.INSPECT FRONT NO. 4 SPEAKER


    E146506E01
  1. Disconnect the K14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER
OK

REPLACE BOX SPEAKER  

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)


    E150805E01
  1. Disconnect the K16 amplifier connector.

  1. Disconnect the K10, K12, O2 and O8 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    K16-7 (FL-) - Body ground
    K16-2 (FR+) - Body ground
    K16-6 (FR-) - Body ground
    K16-3 (RL+) - Body ground
    K16-9 (RL-) - Body ground
    K16-10 (RR+) - Body ground
    K16-4 (RR-) - Body ground
    K10-1 (+) - Body ground
    K10-2 (-) - Body ground
    K12-1 (+) - Body ground
    K12-2 (-) - Body ground
    O2-4 (+) - Body ground
    O2-2 (-) - Body ground
    O8-4 (+) - Body ground
    O8-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 3 SPEAKER LH


    E160614E11
  1. Disconnect the N1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER LH
OK


9.INSPECT FRONT NO. 3 SPEAKER RH


    E160614E12
  1. Disconnect the M1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER RH
OK


10.INSPECT FRONT NO. 2 SPEAKER LH


    E144969E06
  1. Disconnect the K12 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWL+) - 4 (TWL-)
    Always
    1.3 to 2.3 Ω
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)



NG
REPLACE FRONT NO. 2 SPEAKER LH
OK


11.INSPECT FRONT NO. 2 SPEAKER RH


    E144969E07
  1. Disconnect the K10 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWR+) - 4 (TWR-)
    Always
    1.3 to 2.3 Ω
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)



NG
REPLACE FRONT NO. 2 SPEAKER RH
OK


12.INSPECT REAR NO. 1 SPEAKER LH


    E144966E06
  1. Disconnect the O7 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE REAR NO. 1 SPEAKER LH
OK


13.INSPECT REAR NO. 1 SPEAKER RH


    E144966E07
  1. Disconnect the O1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE REAR NO. 1 SPEAKER RH
OK


14.INSPECT REAR NO. 2 SPEAKER LH


    E160614E14
  1. Disconnect the O8 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    2.5 to 3.5 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER LH
OK

REPLACE REAR NO. 2 SPEAKER RH