CYLINDER BLOCK > INSPECTION |
| 1. INSPECT CYLINDER BLOCK FOR FLATNESS |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.
| 2. INSPECT CYLINDER BORE |
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
| 3. INSPECT RING GROOVE CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Specified Condition |
| No. 1 | 0.02 to 0.07 mm (0.000787 to 0.00276 in.) |
| No. 2 | 0.02 to 0.06 mm (0.000787 to 0.00236 in.) |
| Oil | 0.07 to 0.15 mm (0.00276 to 0.00590 in.) |
| 4. INSPECT PISTON RING END GAP |
Insert the piston ring into the cylinder bore.
![]() |
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.
![]() |
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
| No. 1 | 0.30 to 0.40 mm (0.0118 to 0.0157 in.) |
| No. 2 | 0.40 to 0.50 mm (0.0157 to 0.0197 in.) |
| Oil (side rail) | 0.10 to 0.40 mm (0.00394 to 0.0157 in.) |
| Item | Specified Condition |
| No. 1 | 1.0 mm (0.0394 in.) |
| No. 2 | 1.1 mm (0.0433 in.) |
| Oil (side rail) | 1.0 mm (0.0394 in.) |
| 5. INSPECT PISTON WITH PIN SUB-ASSEMBLY |
![]() |
Using a micrometer, measure the piston diameter at a right angle to the piston pin center line, 40.7 mm (1.60 in.) from the piston head.
| 6. INSPECT PISTON OIL CLEARANCE |
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 7. INSPECT PISTON PIN OIL CLEARANCE |
![]() |
Check each mark on the piston, piston pin and connecting rod.
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Mark | Specified Condition |
| A | 22.001 to 22.004 mm (0.86618 to 0.86630 in.) |
| B | 22.005 to 22.007 mm (0.86634 to 0.86642 in.) |
| C | 22.008 to 22.010 mm (0.86645 to 0.86653 in.) |
![]() |
Using a micrometer, measure the piston pin diameter.
| Mark | Specified Condition |
| A | 21.997 to 22.000 mm (0.86602 to 0.86614 in.) |
| B | 22.001 to 22.003 mm (0.86618 to 0.86626 in.) |
| C | 22.004 to 22.006 mm (0.86630 to 0.86642 in.) |
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bush.
| Mark | Specified Condition |
| A | 22.005 to 22.008 mm (0.86634 to 0.86645 in.) |
| B | 22.009 to 22.011 mm (0.86649 to 0.86657 in.) |
| C | 22.012 to 22.014 mm (0.86661 to 0.86669 in.) |
Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.
Subtract the piston pin diameter measurement from the bush inside diameter measurement.
| 8. INSPECT CONNECTING ROD SUB-ASSEMBLY |
![]() |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for bend.
![]() |
Check for twist.
| 9. INSPECT CRANKSHAFT |
![]() |
Using a dial indicator and V-blocks, measure the runout as shown in the illustration.
![]() |
Using a micrometer, measure the diameter of each main journal.
Check each main journal for taper and out-of-round as shown.
![]() |
Using a micrometer, measure the diameter of each crank pin.
Check each crank pin for taper and out-of-round as shown.
| 10. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Clean each main journal and bearing.
![]() |
Align the bearing claw with the claw groove of the cylinder block, and push in the 4 upper bearings.
![]() |
Align the bearing claw with the claw groove of the main bearing cap, and push in the 4 lower bearings.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Examine the front marks and numbers and install the crankshaft bearing caps on the cylinder block.
Temporarily install the 8 crankshaft bearing cap bolts to the inside positions.
![]() |
Tighten the 2 bolts for each bearing cap until the clearance between the crankshaft bearing cap and the cylinder block becomes less than 6 mm (0.236 in.).
![]() |
Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.
Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.
![]() |
Step 1:
Install and uniformly tighten the 16 crankshaft bearing cap bolts in several steps in the order shown in the illustration.
![]() |
Step 2:
Mark the front side of the crankshaft bearing cap bolts with paint.
Tighten the bearing cap bolts another 90° in the order shown in step 1.
Check that the painted marks are now at a 90° angle to the front.
![]() |
Install and uniformly tighten the 8 crankshaft bearing cap bolts in several steps in the sequence shown in the illustration.
Remove the crankshaft bearing caps.
![]() |
Step 1:
Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.
![]() |
Step 2:
Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.
![]() |
Measure the Plastigage at its widest point.
![]() |
If replacing a bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the table below for the appropriate bearing number. There are 5 sizes of standard bearings, marked "1", "2", "3", "4" and "5" accordingly.
| Cylinder block (A) + Crankshaft (B) | Use Bearing |
| 0 - 5 | "1" |
| 6 - 11 | "2" |
| 12 - 17 | "3" |
| 18 - 23 | "4" |
| 24 - 28 | "5" |
| Item | Mark | Specified Condition |
| Cylinder block main journal bore diameter (A) | "00" | 77.000 mm (3.03149 in.) |
| "01" | 77.001 mm (3.03152 in.) | |
| "02" | 77.002 mm (3.03156 in.) | |
| "03" | 77.003 mm (3.03160 in.) | |
| "04" | 77.004 mm (3.03164 in.) | |
| "05" | 77.005 mm (3.03168 in.) | |
| "06" | 77.006 mm (3.03172 in.) | |
| "07" | 77.007 mm (3.03176 in.) | |
| "08" | 77.008 mm (3.03180 in.) | |
| "09" | 77.009 mm (3.03184 in.) | |
| "10" | 77.010 mm (3.03188 in.) | |
| "11" | 77.011 mm (3.03192 in.) | |
| "12" | 77.012 mm (3.0396 in.) | |
| "13" | 77.013 mm (3.03200 in.) | |
| "14" | 77.014 mm (3.03204 in.) | |
| "15" | 77.015 mm (3.03208 in.) | |
| "16" | 77.016 mm (3.03211 in.) | |
| Crankshaft main journal diameter (B) | "00" | 71.999 to 72.000 mm (2.83460 to 2.83464 in.) |
| "01" | 71.998 to 71.999 mm (2.83456 to 2.83460 in.) | |
| "02" | 71.997 to 71.998 mm (2.83452 to 2.83456 in.) | |
| "03" | 71.996 to 71.997 mm (2.83448 to 2.83452 in.) | |
| "04" | 71.995 to 71.996 mm (2.83440 to 2.83448 in.) | |
| "05" | 71.994 to 71.995 mm (2.83440 to 2.83444 in.) | |
| "06" | 71.993 to 71.994 mm (2.83436 to 2.83440 in.) | |
| "07" | 71.992 to 71.993 mm (2.83432 to 2.83436 in.) | |
| "08" | 71.991 to 71.992 mm (2.83428 to 2.83432 in.) | |
| "09" | 71.990 to 71.991 mm (2.83424 to 2.83428 in.) | |
| "10" | 71.989 to 71.990 mm (2.83420 to 2.83424 in.) | |
| "11" | 71.988 to 71.989 mm (2.83416 to 2.83420 in.) |
| Mark | Specified Condition |
| "1" | 2.488 to 2.491 mm (0.0980 to 0.0981 in.) |
| "2" | 2.491 to 2.494 mm (0.0981 to 0.0982 in.) |
| "3" | 2.494 to 2.497 mm (0.0982 to 0.0983 in.) |
| "4" | 2.497 to 2.500 mm (0.0983 to 0.0984 in.) |
| "5" | 2.500 to 2.503 mm (0.0984 to 0.0985 in.) |
| 11. INSPECT CONNECTING ROD OIL CLEARANCE |
Install the crankshaft bearing .
Install the crankshaft .
![]() |
Lay a strip of Plastigage across the crank pin.
![]() |
Check that the protrusion of the connecting rod cap is facing the correct direction.
Apply a light coat of engine oil to the threads of the connecting rod cap bolts.
![]() |
Step 1:
Install and uniformly tighten the connecting rod cap bolts in sequence.
![]() |
Step 2:
Mark the front side of each connecting rod cap bolt with paint.
Tighten the bearing cap bolts in step 1 another 90°.
Remove the 2 bolts, connecting rod cap and lower bearing.
![]() |
Measure the Plastigage at its widest point.
![]() |
If replacing a bearing, replace it with one that has the same number marked on the connecting rod. There are 4 sizes of standard bearings, marked "1 ", "2", "3" and "4" accordingly.
| Mark | Specified Condition |
| 1 | 1.484 to 1.487 mm (0.05843 to 0.05854 in.) |
| 2 | 1.486 to 1.490 mm (0.05850 to 0.05866 in.) |
| 3 | 1.489 to 1.493 mm (0.05862 to 0.05878 in.) |
| 4 | 1.492 to 1.496 mm (0.05874 to 0.05900 in.) |
Remove the crankshaft .
Remove the crankshaft bearing.
| 12. INSPECT CONNECTING ROD BOLT |
![]() |
Using a vernier caliper, measure the tension portion diameter of the bolt.
| 13. INSPECT CRANKSHAFT BEARING CAP SET BOLT |
![]() |
Using a vernier caliper, measure the tension portion diameter of the bolt.