Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here


HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply new engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets, O-rings and oil seals with new ones.



1. REMOVE OIL PRESSURE SWITCH


    A158548
  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.



2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A158541
  1. Remove the engine coolant temperature sensor and gasket.



3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


    A158568
  1. Remove the 2 water drain cocks.



4. REMOVE VVT SENSOR


    A158546E02
  1. Remove the 2 bolts and 2 VVT sensors from the cylinder head LH and RH.



5. REMOVE CRANKSHAFT POSITION SENSOR


    A158545
  1. Remove the bolt and crankshaft position sensor.



6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A158547E02
  1. Remove the 2 bolts and 2 camshaft timing oil control valves from the cylinder head LH and RH.

  1. Remove the 2 O-rings.



7. REMOVE OIL CONTROL VALVE FILTER


    A072942E06
  1. Remove the 2 unions, 2 filters and 2 gaskets from cylinder head LH and RH.



8. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Remove the drain pipe cap.



    A134828E02
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    1. Put the disposal container beneath the drain hose to collect the oil from the oil filter cover.
    2. Drain hose inside diameter: 8 mm (0.315 in.)
    3. Drain hose length: 900 mm (2.95 ft.)



9. DISCONNECT NO. 2 OIL COOLER HOSE


A151242E01


10. DISCONNECT OIL COOLER HOSE


11. REMOVE OIL COOLER ASSEMBLY


    A151243
  1. Remove the oil cooler union bolt, plate washer and oil cooler.



12. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


    A151244
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and O-ring.



13. DISCONNECT NO. 1 WATER BY-PASS HOSE


14. DISCONNECT NO. 2 WATER BY-PASS HOSE


15. DISCONNECT NO. 3 WATER BY-PASS HOSE


16. REMOVE WATER INLET HOUSING


    A076337E01
  1. Remove the 5 bolts and water inlet housing.

  1. Remove the O-ring and gasket from the water outlet pipe and water pump.



17. REMOVE REAR WATER BY-PASS JOINT


    A076534E01
  1. Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. Remove the O-ring from the No. 1 water outlet pipe.



18. REMOVE OIL FILLER CAP SUB-ASSEMBLY


A158574


19. REMOVE OIL FILLER CAP HOUSING
  1. Remove the 2 nuts, oil filler cap housing and gasket.



20. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.



21. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



22. REMOVE VENTILATION VALVE SUB-ASSEMBLY
  1. Remove the ventilation valve.



23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A072944E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



24. REMOVE CRANKSHAFT PULLEY


    A072945E01
  1. Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.



    G038065E10
  1. Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.



    A072947E03
  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)



25. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.



26. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A151269E01
  1. Remove the 10 bolts and 2 nuts.



    A151270
  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.



27. REMOVE OIL STRAINER SUB-ASSEMBLY


    A151271
  1. Remove the 2 nuts, oil strainer and gasket.



28. REMOVE OIL PAN SUB-ASSEMBLY


    A151272E02
  1. Remove the 17 bolts (A, B, C) and 2 nuts.



    A072953E03
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.



    A076306E01
  1. Remove the O-ring from the cylinder block.



29. REMOVE ENGINE REAR OIL SEAL RETAINER


    A076247E02
  1. Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.



30. REMOVE REAR CRANKSHAFT OIL SEAL


    A076248E03
  1. Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the rear oil seal retainer.



31. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A158566E01
  1. Remove the 24 bolts labeled A and B, and 2 nuts.



    G038102E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the cylinder head LH side.



32. REMOVE WATER PUMP ASSEMBLY


    A158567
  1. Remove the 8 bolts, water pump and gasket.



33. REMOVE FRONT CRANKSHAFT OIL SEAL


    A134550E02
  1. If the timing chain case is removed:

    1. Using a screwdriver and wooden block, pry out the oil seal.

      HINT:
      Tape the screwdriver tip before use.

      NOTICE:
      Do not damage the surface of the oil seal press fit hole and crankshaft.



34. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.



    A158627E01
  1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts and chain tensioner.



35. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.



36. REMOVE NO. 1 IDLE GEAR SHAFT


    A072959E01
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.



37. REMOVE NO. 2 CHAIN VIBRATION DAMPER


    G036844E01
  1. Remove the 2 No. 2 chain vibration dampers.



38. REMOVE NO. 1 CHAIN
  1. Remove the No. 1 chain.



39. REMOVE CRANKSHAFT TIMING SPROCKET


    A158530
  1. Remove the crankshaft timing sprocket.



40. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A076292E01
  1. Remove the 2 bolts and No. 1 chain vibration damper.



41. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)


    G038067E01
  1. While raising the No. 2 chain tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    G038110E01
  1. Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing sprocket and No. 2 chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear.



42. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


    A072962E01
  1. Remove the bolt and No. 2 chain tensioner.



43. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)


    G038075E01
  1. While raising the No. 3 chain tensioner, insert a pin of φ 1.0 mm (0.0394 in.) into the hole to fix it.



    G038112E01
  1. Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing sprocket and No. 2 chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear.



44. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    A072965E01
  1. Remove the bolt and No. 3 chain tensioner.



45. REMOVE NO. 1 CAMSHAFT AND NO. 2 CAMSHAFT (for Bank 1)

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.



    A072966E06
  1. Remove the No. 1 and No. 2 camshafts.

    1. Rotate the camshafts counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face each direction as shown in the illustration.



    2. A072967E19
    3. Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    4. Remove the 8 bearing caps and 2 camshafts.



46. REMOVE NO. 1 CAMSHAFT BEARING (for Bank 1)


A158703


47. REMOVE NO. 2 CAMSHAFT BEARING (for Bank 1)


A158539


48. REMOVE NO. 3 CAMSHAFT AND NO. 4 CAMSHAFT (for Bank 2)


    A072968E19
  1. Remove the No. 3 and No. 4 camshafts.

    1. Uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    2. Remove the 8 bearing caps and 2 camshafts.



49. REMOVE CYLINDER HEADS


    A072969E13
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 2 bolts in the sequence shown in the illustration. Remove the 2 cylinder head bolts and plate washers.



    A072970E08
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 16 bolts in the sequence shown in the illustration. Remove the 16 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.



    A072971E01
  1. Lift the cylinder head from the dowels on the cylinder block, and place the 2 cylinder heads on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift off, pry between the cylinder head and cylinder block with a screwdriver.



50. REMOVE CYLINDER HEAD GASKET


51. REMOVE NO. 2 CYLINDER HEAD GASKET


52. REMOVE NO. 1 WATER OUTLET PIPE


    A151268
  1. Remove the bolt, 2 nuts and water outlet pipe.



53. REMOVE KNOCK SENSOR


    A076270E01
  1. Remove the 2 bolts and 2 knock sensors.