PROPELLER SHAFT ASSEMBLY (for 4WD) > INSTALLATION |
| 1. INSTALL PROPELLER SHAFT ASSEMBLY (for 2 Joint Type) |

![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft to the differential side with the 4 bolts and 4 nuts.
![]() |
Align the matchmarks on the propeller shaft flange and transfer flange.
Install the propeller shaft to the transfer side with the 4 nuts.
| 2. MEASURE TRANSFER AND DIFFERENTIAL FLANGE ANGLE (for 3 Joint Type) |
![]() |
Using SST, measure and record the angle of the transfer flange (A).
![]() |
Using SST, measure and record the angle of the rear differential flange (B).
| 3. TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 3 Joint Type) |

![]() |
w/o Bearing Washer:
Temporarily install the center support bearing to the crossmember with the 2 mounting bolts.
![]() |
w/ Bearing Washer:
Temporarily install the center support bearing to the crossmember with the 2 bearing washers and 2 mounting bolts.
![]() |
Align the matchmarks on the flange yoke and transfer flange.
Install the propeller shaft to the transfer side with the 4 nuts.
![]() |
Align the matchmarks on the flange yoke and differential flange.
Install the propeller shaft to the differential side with the 4 bolts and 4 nuts.
| 4. TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 3 Joint Type) |
With the vehicle empty and all 4 tires supported by a lift, or with the vehicle suspension in the full rebound position, adjust the center bearing so that dimension A (the distance from the front surface of the center bearing housing to the back surface of the intermediate shaft) is as shown in the chart below.

| Vehicle model | Vehicle condition | Dimension A |
| All model | Tires supported and vehicle empty (When using drive-on type lift) | 26.0 mm (1.024 in.) |
| Full rebound position (When using 2 post lift) | 26.0 mm (1.024 in.) |
![]() |
Check that the center line of the bracket is at right angles to the shaft axial direction.
Tighten the 2 mounting bolts.
| 5. INSPECT PROPELLER SHAFT JOINT ANGLE (for 3 Joint Type) |
Measure the No. 1 joint angle.
Using SST, measure and record the angle of the intermediate shaft (C).

![]() |
Subtract the angle of the transfer flange (A) measured before installing the propeller shaft from the angle of the intermediate shaft (C) to calculate the No. 1 joint angle.
| Intermediate Shaft Angle Measured Value (C) | transfer Flange Angle Measured Value (A) | No. 1 Joint Angle (Calculated Value) (C) - (A) |
| 2°30' (2.50°) | 3°45' (3.75°) | -1°15' (-1.25°) |
| Vehicle model | No. 1 joint angle |
| UCK56L-THADKA | -0°07' +/-0°60' (-0.12° +/-1.00°) |
| UCK56L-THADKA*1 | -0°07' +/-0°60' (-0.12° +/-1.00°) |
| USK56L-THTDKA | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-THTDGA | 0°52' +/-0°60' (0.87° +/-1.00°) |
| UCK56L-CRASKA UCK56L-CRALKA | 0°51' +/-0°60' (0.85° +/-1.00°) |
| UCK56L-CRASKA*2 UCK56L-CRALKA*2 | 0°51' +/-0°60' (0.85° +/-1.00°) |
| UCK57L-CHASKA | 1°07' +/-0°60' (1.12° +/-1.00°) |
| USK56L-CRTSKA USK56L-CRTLKA | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-CRTSKA*2 USK56L-CRTLKA*2 | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-CRTSGA USK56L-CRTLGA | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-CRTSGA*2 USK56L-CRTLGA*2 | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK57L-CHTSKA | 1°07' +/-0°60' (1.12° +/-1.00°) |
| USK57L-CHTSGA | 1°07' +/-0°60' (1.12° +/-1.00°) |
| UCK56L-PSASKA UCK56L-PSALKA | 0°51' +/-0°60' (0.85° +/-1.00°) |
| UCK56L-PSASKA*2 UCK56L-PSALKA*2 | 0°51' +/-0°60' (0.85° +/-1.00°) |
| USK56L-PSTSKA USK56L-PSTLKA | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-PSTSKA*2 USK56L-PSTLKA*2 | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-PSTSGA USK56L-PSTLGA | 0°52' +/-0°60' (0.87° +/-1.00°) |
| USK56L-PSTSGA*2 USK56L-PSTLGA*2 | 0°52' +/-0°60' (0.87° +/-1.00°) |
Measure the No. 2 joint angle.
Using SST, measure and record the angle of the propeller shaft (D).

Subtract the angle of the propeller shaft (D) from the angle of the intermediate shaft (C) to calculate the No. 2 joint angle.
| Intermediate Shaft Angle Measured Value (C) | Propeller Shaft Angle Measured Value (D) | No. 2 Joint Angle (Calculated Value) (C) - (D) |
| 2°30' (2.50°) | 5°45' (5.75°) | -3°15' (-3.25°) |

| Vehicle model | No. 2 joint angle |
| UCK56L-THADKA | -1°35' +/-0°60' (-1.58° +/-1.00°) |
| UCK56L-THADKA*1 | -2°09' +/-0°60' (-2.15° +/-1.00°) |
| USK56L-THTDKA | -3°19' +/-0°60' (-3.32° +/-1.00°) |
| USK56L-THTDGA | -3°19' +/-0°60' (-3.32° +/-1.00°) |
| UCK56L-CRASKA UCK56L-CRALKA | -2°43' +/-0°60' (-2.72° +/-1.00°) |
| UCK56L-CRASKA*2 UCK56L-CRALKA*2 | -2°28' +/-0°60' (-2.47° +/-1.00°) |
| UCK57L-CHASKA | -1°56' +/-0°60' (-1.93° +/-1.00°) |
| USK56L-CRTSKA USK56L-CRTLKA | -2°23' +/-0°60' (-2.38° +/-1.00°) |
| USK56L-CRTSKA*2 USK56L-CRTLKA*2 | -2°29' +/-0°60' (-2.48° +/-1.00°) |
| USK56L-CRTSGA USK56L-CRTLGA | -2°23' +/-0°60' (-2.38° +/-1.00°) |
| USK56L-CRTSGA*2 USK56L-CRTLGA*2 | -2°29' +/-0°60' (-2.48° +/-1.00°) |
| USK57L-CHTSKA | -1°39' +/-0°60' (-1.65° +/-1.00°) |
| USK57L-CHTGKA | -1°39' +/-0°60' (-1.65° +/-1.00°) |
| UCK56L-PSASKA UCK56L-PSALKA | -2°15' +/-0°60' (-2.25° +/-1.00°) |
| UCK56L-PSASKA*2 UCK56L-PSALKA*2 | -2°43' +/-0°60' (-2.72° +/-1.00°) |
| USK56L-PSTSKA USK56L-PSTLKA | -2°32' +/-0°60' (-2.53° +/-1.00°) |
| USK56L-PSTSKA*2 USK56L-PSTLKA*2 | -2°29' +/-0°60' (-2.48° +/-1.00°) |
| USK56L-PSTSGA USK56L-PSTLGA | -2°32' +/-0°60' (-2.53° +/-1.00°) |
| USK56L-PSTSGA*2 USK56L-PSTLGA*2 | -2°29' +/-0°60' (-2.48° +/-1.00°) |
Measure the No. 3 joint angle.
Subtract the angle of the rear differential flange (B) measured before installing the propeller shaft from the angle of the propeller shaft (D) to calculate the No. 3 joint angle.
| Propeller Shaft Angle Measured Value (D) | Rear Differential Flange Angle Measured Value (B) | No. 3 Joint Angle (Calculated Value) (D) - (B) |
| 5°45' (5.75°) | 2°30' (2.50°) | 3°15' (3.25°) |

| Vehicle model | No. 3 joint angle |
| UCK56L-THADKA | 3°37' +/-0°60' (3.62° +/-1.00°) |
| UCK56L-THADKA*1 | 4°09' +/-0°60' (4.15° +/-1.00°) |
| USK56L-THTDKA | 3°22' +/-0°60' (3.37° +/-1.00°) |
| USK56L-THTDGA | 3°22' +/-0°60' (3.37° +/-1.00°) |
| UCK56L-CRASKA UCK56L-CRALKA | 3°49' +/-0°60' (3.82° +/-1.00°) |
| UCK56L-CRASKA*2 UCK56L-CRALKA*2 | 3°34' +/-0°60' (3.57° +/-1.00°) |
| UCK57L-CHASKA | 4°17' +/-0°60' (4.28° +/-1.00°) |
| USK56L-CRTSKA USK56L-CRTLKA | 2°59' +/-0°60' (2.98° +/-1.00°) |
| USK56L-CRTSKA*2 USK56L-CRTLKA*2 | 3°05' +/-0°60' (3.08° +/-1.00°) |
| USK56L-CRTSGA USK56L-CRTLGA | 2°59' +/-0°60' (2.98° +/-1.00°) |
| USK56L-CRTSGA*2 USK56L-CRTLGA*2 | 3°05' +/-0°60' (3.08° +/-1.00°) |
| USK57L-CHTSKA | 3°29' +/-0°60' (3.48° +/-1.00°) |
| USK57L-CHTSGA | 3°29' +/-0°60' (3.48° +/-1.00°) |
| UCK56L-PSASKA UCK56L-PSALKA | 3°53' +/-0°60' (3.88° +/-1.00°) |
| UCK56L-PSASKA*2 UCK56L-PSALKA*2 | 4°19' +/-0°60' (4.32° +/-1.00°) |
| USK56L-PSTSKA USK56L-PSTLKA | 3°38' +/-0°60' (3.63° +/-1.00°) |
| USK56L-PSTSKA*2 USK56L-PSTLKA*2 | 3°35' +/-0°60' (3.58° +/-1.00°) |
| USK56L-PSTSGA USK56L-PSTLGA | 3°38' +/-0°60' (3.63° +/-1.00°) |
| USK56L-PSTSGA*2 USK56L-PSTLGA*2 | 3°35' +/-0°60' (3.58° +/-1.00°) |
| 6. ADJUST PROPELLER SHAFT ANGLE (for 3 Joint Type) |
Adjust the No. 1, No. 2 and No. 3 joint angle.
Support the propeller shaft with a jack.
Remove the 2 center bearing mounting bolts.
Slowly lower the jack, and disconnect the center bearing.
Select an appropriate center support bearing washer thickness from the table below, and obtain a washer set.
| Thickness |
| 2.0 mm (0.0787 in.) |
| 4.5 mm (0.1772 in.) |
| 6.5 mm (0.2559 in.) |
| 9.0 mm (0.3543 in.) |
| 11.0 mm (0.4331 in.) |
| 13.5 mm (0.5315 in.) |
| 7. INSTALL TRANSFER HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 8. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY |
![]() |
Install the insulator bracket with the 2 bolts.