Home › DRIVE LINE › JF1A TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSFER OIL PUMP PLATE


    C159613
  1. Remove the 4 bolts and oil pump plate, oil pump drive rotor and oil pump driven rotor.

    NOTICE:
    Do not drop the oil pump drive rotor and oil pump driven rotor.



2. REMOVE TRANSFER CASE STRAIGHT PIN


    C162213E01
  1. Remove the 2 straight pins.

    NOTICE:
    Do not drop the straight pins.



3. REMOVE TRANSFER CASE PLUG


    C159727
  1. Using a 10 mm hexagon wrench, remove the case plug, compression spring, ball and relief valve seat.



4. REMOVE TRANSFER OIL PUMP PLATE OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the oil pump plate.

    NOTICE:
    Be careful not to damage the oil seal and oil pump plate contact surfaces.



5. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C159614
  1. Using a chisel and hammer, loosen the staked part of the lock nut.



    C159615E01
  1. Using SST to hold the companion flange, remove the lock nut.

    SST
    09330-00021  



    C159616E01
  1. Using SST, remove the companion flange.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



6. REMOVE TRANSFER CASE FRONT OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the front case.

    NOTICE:
    Be careful not to damage the front case contact surfaces.



7. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C159617
  1. Using a chisel and hammer, loosen the staked part of the lock nut.



    C159618E01
  1. Using SST to hold the companion flange, remove the lock nut.

    SST
    09330-00021  



    C159619E01
  1. Using SST, remove the companion flange.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



8. REMOVE TRANSFER CASE REAR OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the rear case.

    NOTICE:
    Be careful not to damage the rear case contact surfaces.



9. REMOVE NO. 1 TRANSFER CASE PLUG


    C162211
  1. Remove the case plug, compression spring and pin.



10. REMOVE TRANSFER CASE PLUG


    C159725
  1. Using a 10 mm hexagon wrench, remove the case plug.



11. REMOVE REAR TRANSFER CASE


    C159620
  1. Remove the 14 bolts.

  1. Remove the rear case.

    HINT:
    If necessary, tap the rear case with a plastic-faced hammer to remove it.



12. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK


    C159623
  1. Using 2 screwdrivers and a hammer, tap out the 3 shift fork shaft snap rings.



    C159621
  1. Remove the bolt. Then remove the No. 2 gear shift fork together with the high and low clutch sleeve from the shift actuator.



13. REMOVE NO. 1 TRANSFER GEAR SHIFT FORK


    C159622
  1. Remove the bolt. Then remove the No. 1 gear shift fork together with the front drive clutch sleeve from the shift actuator.



14. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


    C159624
  1. Remove the 3 bolts. Then remove the shift actuator from the rear case.



15. REMOVE REAR OUTPUT SHAFT


    C173484
  1. Using a snap ring expander, remove the snap ring.



    C111628E01
  1. Using a plastic-faced hammer, carefully tap the case rear, and remove the output shaft together with the drive chain and driven sprocket.

  1. Remove the output shaft and driven sprocket from the drive chain.

    NOTICE:
    Do not drop the transfer output washer.



16. REMOVE SIDE GEAR SHAFT HOLDER BEARING


    C160519
  1. Using a screwdriver, remove the snap ring.



    C160518
  1. Using a screwdriver, remove the bearing.



17. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C159718
  1. Remove the 3 bolts and oil separator.



18. REMOVE TRANSFER CASE MAGNET


19. REMOVE INPUT SHAFT ASSEMBLY


    C159719
  1. Using a 10 mm hexagon wrench, remove the 2 case plugs from the front case.



    C160522
  1. Using a snap ring expander, remove the snap ring. Then remove the input shaft from the front case.



20. REMOVE TRANSFER LOW PLANETARY RING GEAR


    F043456
  1. Using a screwdriver, remove the snap ring. Then remove the low planetary ring gear from the front case.



21. REMOVE TRANSFER DRIVEN SPROCKET BEARING


    C160357
  1. Using a screwdriver, remove the snap ring. Then remove the driven sprocket bearing from the front case.



22. REMOVE TRANSFER OIL SEAL RING


    C162471E01
  1. Remove the oil seal ring from the input shaft.



23. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486E01
  1. Remove the oil seal ring from the input shaft.



24. REMOVE TRANSFER INPUT SHAFT BEARING


    C159629
  1. Using a snap ring expander, remove the snap ring.



    C159630E01
  1. Using SST and a press, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the low planetary gear.



25. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY


    C159709
  1. Using a screwdriver, remove the snap ring.

  1. Remove the transfer low planetary gear assembly and transfer low planetary gear spline piece from the transfer input shaft.



26. REMOVE TRANSFER INPUT SHAFT PLUG


    C159734E01
  1. Using SST and a hammer, tap out the input shaft plug.

    SST
    09316-60011   (09316-00011)



27. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER


    C159712
  1. Using 2 screwdrivers, tap out the snap ring. Then remove the output shaft spacer and front output shaft needle roller bearing from the output shaft.



28. REMOVE TRANSFER SYNCHROMESH SHIFTING KEY SPRING


    C159713
  1. Using a snap ring expander, remove the snap ring. Then remove the synchromesh shifting key spring and synchromesh shifting key from the output shaft.



29. REMOVE TRANSFER CLUTCH HUB
  1. Using a snap ring expander, remove the snap ring.



    C159714E01
  1. Using SST and a press, press out the clutch hub.

    SST
    09527-10011  

    NOTICE:
    Be careful not to drop or damage the output shaft.



30. REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING


    C159716E01
  1. Using SST and a press, press out the bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the output shaft.

  1. Remove the drive sprocket and drive sprocket bearing.

  1. Remove the synchronizer ring set.



31. REMOVE TRANSFER DRIVE CLUTCH HUB


    C159715
  1. Using 2 screwdrivers, tap out the snap ring.



    C159717E01
  1. Using SST and a press, press out the drive clutch hub.

    SST
    09527-10011  



    D030010E02
  1. Remove the 2 No. 1 synchromesh shifting key springs from the drive clutch hub.