Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER OIL SEAL (for 4WD)

FRONT DIFFERENTIAL CARRIER OIL SEAL (for 4WD) > REPLACEMENT

for Preparation Click here



1. DRAIN DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. for Rear Differential:

    1. Remove the filler plug and gasket.

    2. Remove the drain plug and gasket, and drain the oil.

    3. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY
  1. Remove the differential carrier (Click here).



3. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY


    C159258
  1. Remove the 4 bolts.

  1. Using a plastic-faced hammer, remove the differential tube.



4. REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT


    C159261E01
  1. Using SST and a hammer, unstake the nut.

    SST
    09930-00010  



    C159262E01
  1. Using SST to hold the companion, remove the nut.

    SST
    09330-00021   (09330-00030)



5. REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT SUB-ASSEMBLY


    C159263E01
  1. Using SST, remove the companion flange from the differential carrier.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



6. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


    C159264E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  



7. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


8. REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER


    C160133E01
  1. Remove the bolts B and front differential front support assembly LH.

  1. Remove the bolts A.

  1. Using a plastic-faced hammer, tap out the bearing retainer.



9. REMOVE FRONT DIFFERENTIAL CASE
  1. Remove the differential case from the differential carrier.



10. REMOVE DIFFERENTIAL DRIVE PINION


    C159434E01
  1. Set the differential carrier to an overhaul stand as shown in the illustration.

  1. Using a press, press out the drive pinion.

    NOTICE:
    Do not drop the drive pinion.



11. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING
  1. Remove the bearing (inner race) from the differential carrier.



12. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


13. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new bearing spacer.



14. TEMPORARILY INSTALL DIFFERENTIAL DRIVE PINION


15. INSTALL FRONT DIFFERENTIAL CASE


16. INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER


    C159274E01
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential carrier and side bearing retainer.

  1. Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.

  1. Apply seal packing to the side bearing retainer as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the side bearing retainer within 10 minutes of applying seal packing.



    C160133E01
  1. Install the front differential cross shaft bearing retainer and front differential front support assembly LH with the 11 bolts (A), and 3 bolts (B).

    Torque:
    for bolt A:
    65 N*m{ 633 kgf*cm , 48 ft.*lbf }
    for bolt B:
    155 N*m{ 1581 kgf*cm , 114 ft.*lbf }



17. INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING


    C159445E01
  1. Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

    SST
    09316-60011   (09316-00041)



18. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


19. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL


    C159273E01
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09502-12010  
    09316-60011   (09316-00041)

    Standard oil seal depth:
    5.6 to 6.6 mm (0.221 to 0.260 in.)

  1. Coat the lip of the oil seal with MP grease.



20. INSTALL FRONT DRIVE PINION COMPANION FLANGE FRONT SUB-ASSEMBLY


    C159263E03
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



21. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C159272E01
  1. Using SST to hold the companion flange.

    SST
    09330-00021   (09330-00030)

  1. Coat the threads of a new nut with hypoid gear oil.

  1. Install the nut by tightening it until the standard preload is reached.

    Torque:
    451 N*m{ 4599 kgf*cm , 332 ft.*lbf } or less



    C159874
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard preload (at starting):
    Bearing
    Specified Condition
    New
    3.0 to 3.5 N*m (31 to 35 kgf*cm, 27 to 30 in.*lbf)
    Reused
    2.1 to 2.4 N*m (22 to 24 kgf*cm, 19 to 21 in.*lbf)

    If the preload is greater than the specification, replace the bearing spacer.
    If the preload is less than the specification, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

    Torque:
    451 N*m{ 4599 kgf*cm , 332 ft.*lbf } or less

    If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload procedure.

    HINT:
    Do not loosen the nut to reduce the preload.



22. INSPECT TOTAL PRELOAD


    C159874
  1. With the drive pinion contacting the tooth side of the ring gear, use a torque wrench to measure the total preload.

    Standard Drive Pinion Preload Plus:
    Bearing
    Specified Condition
    New
    1.6 to 2.4 N*m(16 to 25 kgf*cm, 14 to 21 in.*lbf)
    Reused
    1.3 to 2.1 N*m(14 to 22 kgf*cm, 12 to 19 in.*lbf)



23. STAKE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT


    C160139
  1. Using a chisel and hammer, stake the nut.



24. INSTALL DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY


    C159276
  1. Install a new snap ring onto the side gear inter shaft.

  1. Using a plastic-faced hammer, install the side gear inter shaft onto the differential case.

  1. Check that there is 2 to 3 mm (0.0788 to 0.118 in.) of play in the axial direction.

  1. Check that the side gear inter shaft does not come out when trying to pull it out by hand.



25. INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY


    C159277E01
  1. Remove any old FIPG material and be careful not to drop oil on the contact surfaces of the differential tube and bearing retainer.

  1. Clean the contact surfaces with any residual FIPG material using gasoline or alcohol.

  1. Apply seal packing to the bearing retainer as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the differential tube within 10 minutes of applying seal packing.

  1. Install the differential tube onto the bearing retainer.



    C159258
  1. Clean the threads of 4 new bolts and the retainer bolt holes with toluene or trichloroethylene.

  1. Apply adhesive to 2 to 3 threads of each bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf } or less



26. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
  1. Install the front differential carrier (Click here).



27. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.05 to 2.15 liters (2.2 to 2.3 US qts., 1.8 to 1.9 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.40 to 3.50 liters (3.6 to 3.7 US qts., 3.0 to 3.1 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.)
    4WD
    1GR-FE and 2UZ-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.2 to 4.3 US qts., 3.5 to 3.6 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.8 to 4.9 US qts., 4.0 to 4.1 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }