Home › ENGINE ยท 2UZ-FE › IGNITION › IGNITION COIL AND SPARK PLUG

IGNITION COIL AND SPARK PLUG > INSTALLATION

for Preparation Click here



1. INSTALL SPARK PLUG
  1. Using a 16 mm plug wrench, install the 8 spark plugs.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



2. INSTALL IGNITION COIL ASSEMBLY


    A191542
  1. Install the 8 ignition coils with the 8 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 8 ignition coil connectors.



3. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 1)


A191536E01
  1. Install the air switching valve with the 3 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Do not hold the bracket of the air switching valve.



4. INSTALL NO. 3 AIR TUBE


A153518
  1. Temporarily install a new gasket and the No. 3 air tube to the exhaust manifold side with the 2 nuts.

  1. Install a new gasket and the No. 3 air tube to the air switching valve side with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the 2 nuts on the exhaust manifold side.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. INSTALL NO. 2 AIR HOSE


    A153516
  1. Install the No. 2 air hose.



    A191535
  1. Connect the air pump connector.

  1. Connect the fuel hose clamp.



6. INSTALL FRONT FENDER APRON SEAL REAR LH


    A159336
  1. Install the fender apron seal with the 5 clips.



7. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 2)


A153513E01
  1. Install the air switching valve with the 3 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Do not hold the bracket of the air switching valve.



8. INSTALL NO. 2 AIR TUBE


A153512
  1. Temporarily install a new gasket and the No. 2 air tube to the exhaust manifold side with the 2 nuts.

  1. Install a new gasket and the No. 2 air tube to the air switching valve side with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the 2 nuts on the exhaust manifold side.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A153510
  1. Connect the air pump connector.

  1. Connect the wire harness clamp.



9. CONNECT NO. 2 AIR INJECTION SYSTEM HOSE
  1. Connect the air injection system hose to the air switching valve.



10. CONNECT NO. 1 WATER BY-PASS PIPE


    A159337
  1. Connect the water by-pass pipe with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



11. INSTALL FRONT FENDER APRON SEAL REAR RH


    A159335
  1. Install the fender apron seal with the 5 clips.



12. INSTALL AIR CLEANER HOSE ASSEMBLY


    A153488E01
  1. Install the air cleaner hose.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the clamp band end is aligned with the limit mark when the hose clamps is tightened, as indicated by A and B in the illustration.

  1. Connect the vacuum hose and No. 2 ventilation hose.



13. INSTALL THROTTLE BODY COVER ASSEMBLY


    A156184E02
  1. Install the 2 throttle body cover brackets with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A156183E01
  1. Install the throttle body cover with the 2 cap nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }