Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on tester, read the "Data List".

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed is displayed
    -
    CCS Mem Vehicle Spd
    Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
    Actual vehicle speed stored in memory
    -
    Cruise Operation Status
    Shift lever position signal / ON or OFF
    1. for 3UR-FE, 3UR-FBE:
      ON: Shift lever position D (6th, 5th or 4th gear)
      OFF: Shift lever position except D (6th, 5th or 4th gear)
    2. for 1GR-FE, 2UZ-FE:
      ON: Shift lever position D (5th or 4th gear)
      OFF: Shift lever position except D (5th or 4th gear)
    -
    Cruise Control
    Cruise control / ON or OFF
    ON: Cruise control is SET
    OFF: Cruise control is UNSET
    -
    CCS Indicator M-CPU
    CRUISE main indicator light (Main CPU) / ON or OFF
    ON: CRUISE main indicator light is ON
    OFF: CRUISE main indicator light is OFF
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / ON or OFF
    ON ←→ OFF: Changes each time main switch is pushed
    -
    CCS Main SW M-CPU
    Cruise control main switch (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) is SET
    OFF: Cruise control main switch (Main CPU) is UNSET
    -
    Cancel Switch
    CANCEL switch / ON or OFF
    ON: CANCEL switch is SET
    OFF: CANCEL switch is UNSET
    -
    SET/COAST Switch
    -/SET switch / ON or OFF
    ON: -/SET switch is SET
    OFF: -/SET switch is UNSET
    -
    RES/ACC Switch
    +/RES switch / ON or OFF
    ON: +/RES switch is SET
    OFF: +/RES switch is UNSET
    -
    Stop Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Throttle Opening Angle
    Cruise throttle opening angle / min.: 0°, max.: 125°
    Actual demanded throttle angle
    -
    # Codes
    Number of diagnosis codes/Min.: 0, Max.: 255
    -
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Body / Combination Meter / Active Test.

  7. According to the display on tester, perform the "Active Test".

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    CRUISE main indicator light operation
    OFF or ON
    -