BRAKE FLUID > REPLACEMENT |
| 1. REPLACE BRAKE FLUID OF FRONT BRAKE SYSTEM |
![]() |
Connect a vinyl tube to the bleeder plug of the front disc brake caliper.
Depress the brake pedal several times and loosen the bleeder plug. With the brake pedal depressed, bleed fluid from the front disc brake caliper RH and LH.
![]() |
After bleeding the fluid, tighten the bleeder plug and release the brake pedal.
| 2. REPLACE BRAKE FLUID OF REAR BRAKE SYSTEM |
![]() |
Connect a vinyl tube to the bleeder plug of the rear disc brake cylinder.
Depress the brake pedal several times and loosen the bleeder plug. With the brake pedal depressed, bleed fluid from the rear disc brake caliper RH and LH.
![]() |
After bleeding the fluid, tighten the bleeder plug and release the brake pedal.
| 3. CHECK AND ADJUST BRAKE FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level and add fluid if necessary.
| 4. CLEAR DTC |
Clear the DTCs (Click here).
| 5. CHECK AND BLEED BRAKE SYSTEM |
If the following malfunction symptoms occur, air may have entered the brake fluid line. Perform the following air bleed procedures.
| 6. FILL RESERVOIR WITH BRAKE FLUID |
![]() |
Set the brake fluid can upside down on the reservoir.
| 7. BLEED AIR FROM BRAKE MASTER CYLINDER |
![]() |
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Block the outer holes with your fingers, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using a union nut wrench, connect the 2 brake lines to the master cylinder.
| 8. BLEED AIR FROM BRAKE LINE |

Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.
| 9. BLEED AIR FROM VSC ACTUATOR ASSEMBLY |
Depress the brake pedal more than 20 times with the engine off.
Connect the Techstream to the DLC3, and turn the ignition switch ON.
Select AIR BLEEDING on the Techstream.
Bleed the air out of the suction line.
Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.
Loosen the bleeder plug.
Operate the brake actuator to bleed the air using the Techstream.
Check if the operation has stopped by referring to the Techstream display.
Temporarily tighten the bleeder plug.
Repeat the 4 previous steps until all air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat all of the above procedures for the other wheel to bleed the air out of the suction line.
Bleed the air out of the pressure reduction line.
Connect a vinyl tube to one of the bleeder plugs.
Loosen the bleeder plug.
Using the Techstream operate the brake actuator, completely depress the brake pedal and hold it there.
Tighten the bleeder plug, then release the brake pedal.
Repeat the 3 previous steps until all air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.
| 10. CHECK AND ADJUST BRAKE FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level and add fluid if necessary.
| 11. CLEAR DTC |
Clear the DTCs (Click here).
| 12. CHECK DTC |
If any DTC is set, perform the troubleshooting for the DTC (Click here).