Home › ENGINE ยท 3UR-FBE › COOLING › WATER PUMP

WATER PUMP > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A191562E01

  1. Tighten the radiator drain cock plug by hand.



3. REMOVE V-BANK COVER SUB-ASSEMBLY


    A165576E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



4. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



5. REMOVE AIR CLEANER ASSEMBLY


    A162105E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. Unfasten the 4 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A156197E01
  1. Remove the 2 bolts and air cleaner case.



6. DISCONNECT INLET RADIATOR HOSE


7. DISCONNECT OUTLET RADIATOR HOSE


8. REMOVE FAN SHROUD


    A151842
  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt.

  1. Disconnect the reservoir hose from the upper radiator tank.



    A161784
  1. w/ Trailer Towing System:
    Detach the claw to open the No. 1 flexible hose clamp.



    A151821
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the fan bracket.



9. REMOVE NO. 1 WATER BY-PASS HOSE


    A162549
  1. Remove the No. 1 water by-pass hose by disconnect the hose from the water inlet housing and front water by-pass joint.



10. DISCONNECT WATER BY-PASS PIPE (w/ Oil Cooler)


A151836
  1. Disconnect the No. 6 water by-pass hose.

  1. Remove the 3 bolts.

  1. Disconnect the water by-pass pipe with water hose.



11. REMOVE WATER INLET HOUSING


    A158575E02
  1. Disconnect the No. 2 and No. 3 air hoses.

  1. Disconnect the air pump connector.

  1. Disconnect the air pump connector clamp's holder.

  1. Using a clip remover, detach the wire harness clamp.



    A151840E01
  1. Disconnect the No. 5 water by-pass hose.

  1. Remove the air tube bracket bolt.



    A151829E01
  1. Remove the 3 bolts, water inlet housing and No. 3 water by-pass hose.

  1. Remove the gasket from the water pump.



12. REMOVE WATER PUMP PULLEY


    A151837E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



13. REMOVE WATER PUMP ASSEMBLY


    A151828
  1. Remove the 8 bolts, water pump and gasket.