Home › ENGINE ยท 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P050A    Cold Start Idle Air Control System Performance

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
P050A
Insufficient mass air flow at cold start
(2 trip detection logic)
  1. Throttle body
  2. Mass air flow meter
  3. PCV hose
  4. Air cleaner filter
  5. Air induction system
  6. VVT system
  7. ECM
This monitor will run when the engine is started with the engine coolant temperature at -10 to 50°C (14 to 122°F). The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the idle air control at cold start. When the engine is started with the engine coolant temperature at lower than 50°C (122°F), the ECM (PCM) measures the accumulated mass air flow at engine idling. If it does not reach the criteria within 10 seconds, the ECM (PCM) interprets this as a malfunction. The MIL is illuminated and a DTC is set when the malfunction is detected in consecutive driving cycles (2 trip detection logic).
The ETCS (Electronic Throttle Control System) controls the idle speed. The ETCS operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:
When the negative battery terminal is disconnected during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be set with the ISC learning values cleared.
The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A124205E05


MONITOR STRATEGY


Related DTCs
P050A: Cold start idle air speed control system
Required sensors/Components (Main)
Throttle body
Required sensors/Components (Related)
Mass air flow meter
Engine coolant temperature sensor
Frequency of operation
Once per driving cycle
Duration
10 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil control valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348, P1340 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Front oxygen/Air fuel ratio sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or more
Time after engine start
3 seconds or more
Starter
OFF
ECT at engine start
-10°C (14°F) or more
ECT
-10 to 50°C (14 to 122°F)
Engine idling
3 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 3 km/h (1.875 mph)
Time after shift position changed
2 seconds or more
Atmospheric pressure
76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS


Accumulated mass air flow
Less than 116 g (varies with ECT)

INSPECTION PROCEDURE

1.CHECK DTCS

OK:
Any other DTCs are not set.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.

  1. Read the values displayed on the Techstream.

  1. Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

    Result:
    Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.



NG
Go to step 4
OK


3.CHECK THROTTLE BODY
  1. Check for deposits around the throttle valve and throttle valve condition.

    OK:
    No deposits around throttle valve and throttle valve moves smoothly.



NG
Go to step 8

OK
Go to step 9

4.CHECK VVT SYSTEM
  1. Allow the engine to idle after the engine is warmed up.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Turn on Control the VVT System (Bank 1) or Control the VVT System (Bank 2) to advance the valve timing.

  1. Check the engine condition.

    OK:
    The engine stalls or idles roughly when Control the VVT System is ON (VVT system is OK).



NG
Go to step 10
OK


5.CHECK PCV SYSTEM
  1. Allow the engine to idle.

  1. Pinch the positive crankcase ventilation (PCV) hose.

  1. Check the engine rpm.

    OK:
    The engine rpm rises when the PCV hose is pinched.



NG
Go to step 11
OK


6.CHECK AIR CLEANER FILTER
  1. Visually check that the air cleaner filter is not excessively contaminated with dirt or oil.



NG
Go to step 12
OK


7.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .



NG
Go to step 13

OK
Go to step 14

8.REPAIR OR REPLACE THROTTLE BODY
  1. Repair or replace the throttle body (Click here).



NEXT
Go to step 15

9.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 15

10.CHECK AND REPAIR VVT SYSTEM


NEXT
Go to step 15

11.REPAIR OR REPLACE PCV HOSE


NEXT
Go to step 15

12.REPLACE AIR CLEANER FILTER


NEXT
Go to step 15

13.REPAIR OR REPLACE AIR INDUCTION SYSTEM


NEXT
Go to step 15

14.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).


NEXT


15.CHECK DTCS
  1. Check that the engine coolant temperature is -10 to 50°C (14 to 122°F).

  1. Clear the DTC (Click here).

  1. Enter the check mode using the Techstream (Click here).

  1. Allow the engine to idle for 1 minute.

  1. Check that no DTC is present.


NEXT

END