Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    C159604E01


    Wiring color 
    Junction Connector A Side
    Color (CANH Side)
    Color (CANL Side)
    Combination meter ECU (J84)*1
    SB
    W
    Center airbag sensor (J83)
    BR
    W
    Skid control ECU with actuator (A46)
    B
    W

    Wiring color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    DLC3 (J86)
    V
    W
    Main body ECU (J96)*1
    L
    W
    No. 2 junction connector (J94)
    R
    W
    Steering angle sensor (J87)
    G
    W

    HINT:
    1. *1: for V bus
    2. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    3. The connectors can be connected to any terminals on the same side.



  2. NO. 2 JUNCTION CONNECTOR


    C159603E01


    Wiring color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    Bus buffer ECU (J98)*1
    P
    W
    No. 1 junction connector (J93)
    R
    W
    ECM (J92)
    GR
    W
    4WD control ECU (J88)*2
    BE
    W
    Air conditioning amplifier (J85)
    B
    W

    HINT:
    1. *1: w/ Bus Buffer ECU
    2. *2: w/ 4WD
    3. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    4. The connectors can be connected to any terminals on the same side.



  3. NO. 3 JUNCTION CONNECTOR


    C159602E01


    Wiring color 
    Junction Connector A Side
    Color (CANH Side)
    Color (CANL Side)
    Front power seat control ECU and switch LH (J90)*1
    GR
    W
    Multiplex tilt and telescopic ECU (J89)*1
    BE
    W
    Main body ECU (J97)*2
    B
    W
    Combination meter ECU (J95)*2
    Y
    W

    Wiring color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    Outer mirror control ECU (J91)*1
    LG
    W

    HINT:
    1. *1: w/ Seat Memory
    2. *2: for MS bus
    3. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    4. The connectors can be connected to any terminals on the same side.


TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (JUNCTION CONNECTOR)
C135249
Terminal
Terminal Symbol
1
CANH
2
CANL

CHECK DLC3
H102392E69
  1. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Switch Condition
    Specified Condition
    J17-6 (CANH) - J17-14 (CANL)
    V - W
    Ignition switch OFF
    54 to 69 Ω
    J17-6 (CANH) - J17-4 (CG)
    V - W-B
    Ignition switch OFF
    200 Ω or higher
    J17-14 (CANL) - J17-4 (CG)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J17-6 (CANH) - J17-16 (BAT)
    V - P
    Ignition switch OFF
    6 kΩ or higher
    J17-14 (CANL) - J17-16 (BAT)
    W - P
    Ignition switch OFF
    6 kΩ or higher


CHECK SKID CONTROL ECU WITH ACTUATOR

C159476E01

  1. Disconnect the A17 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    A17-5 (CANH) - A17-4 (CANL)
    B - W
    Ignition switch OFF
    54 to 69 Ω
    A17-5 (CANH) - A17-1 (GND1)
    B - W-B
    Ignition switch OFF
    200 Ω or higher
    A17-4 (CANL) - A17-1 (GND1)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    A17-5 (CANH) - A17-16 (+BM)
    B - L
    Ignition switch OFF
    6 kΩ or higher
    A17-4 (CANL) - A17-16 (+BM)
    W - L
    Ignition switch OFF
    6 kΩ or higher


CHECK MAIN BODY ECU

E146976E01

  1. Disconnect the J2, DB and DD ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J2-5 (CANH) - J2-6 (CANL)*1
    L - W
    Ignition switch OFF
    54 to 69 Ω
    J2-5 (CANH) - DD-62 (GND1)*1
    L - W-B
    Ignition switch OFF
    200 Ω or higher
    J2-6 (CANL) - DD-62 (GND1)*1
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J2-5 (CANH) - DB-13 (BECU)*1
    L - GR
    Ignition switch OFF
    6 kΩ or higher
    J2-6 (CANL) - DB-13 (BECU)*1
    W - GR
    Ignition switch OFF
    6 kΩ or higher
    J2-16 (CANP) - J2-15 (CANN)*2
    B - W
    Ignition switch OFF
    108 to 132 Ω
    J2-16 (CANP) - DD-62 (GND1)*2
    B - W-B
    Ignition switch OFF
    200 Ω or higher
    J2-15 (CANN) - DD-62 (GND1)*2
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J2-16 (CANP) - DB-13 (BECU)*2
    B - GR
    Ignition switch OFF
    6 kΩ or higher
    J2-15 (CANN) - DB-13 (BECU)*2
    W - GR
    Ignition switch OFF
    6 kΩ or higher

    HINT:
    1. *1: for V bus
    2. *2: for MS bus


CHECK ECM

C159489E01

  1. Disconnect the A24 and D74 ECM connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    A24-10 (CANH) - A24-11 (CANL)
    GR - W
    Ignition switch OFF
    108 to 132 Ω
    A24-10 (CANH) - D74-81 (E1)
    GR - BR
    Ignition switch OFF
    200 Ω or higher
    A24-11 (CANL) - D74-81 (E1)
    W - BR
    Ignition switch OFF
    200 Ω or higher
    A24-10 (CANH) - A24-3 (+B)
    GR - GR
    Ignition switch OFF
    6 kΩ or higher
    A24-11 (CANL) - A24-3 (+B)
    W - GR
    Ignition switch OFF
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER

C159478E01

  1. Disconnect the J19 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J19-11 (CANH) - J19-12 (CANL)
    B - W
    Ignition switch OFF
    54 to 69 Ω
    J19-11 (CANH) - J19-14 (GND)
    B - W-B
    Ignition switch OFF
    200 Ω or higher
    J19-12 (CANL) - J19-14 (GND)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J19-11 (CANH) - J19-21 (B)
    B - R
    Ignition switch OFF
    6 kΩ or higher
    J19-12 (CANL) - J19-21 (B)
    W - R
    Ignition switch OFF
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR

C162022E01

  1. Disconnect the J46 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J46-13 (CANH) - J46-22 (CANL)
    BR - W
    Ignition switch OFF
    54 to 69 Ω
    J46-13 (CANH) - J46-25 (E1)
    BR - W-B
    Ignition switch OFF
    200 Ω or higher
    J46-22 (CANL) - J46-25 (E1)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J46-13 (CANH) - J17-16 (BAT)
    BR - P
    Ignition switch OFF
    6 kΩ or higher
    J46-22 (CANL) - J17-16 (BAT)
    W - P
    Ignition switch OFF
    6 kΩ or higher


CHECK COMBINATION METER ECU

C159488E03

  1. Disconnect the J28 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J28-33 (CANH) - J28-34 (CANL)*1
    SB - W
    Ignition switch OFF
    108 to 132 Ω
    J28-33 (CANH) - J28-40 (E1)*1
    SB - W-B
    Ignition switch OFF
    200 Ω or higher
    J28-34 (CANL) - J28-40 (E1)*1
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J28-33 (CANH) - J28-18 (B)*1
    SB - LG
    Ignition switch OFF
    6 kΩ or higher
    J28-34 (CANL) - J28-18 (B)*1
    W - LG
    Ignition switch OFF
    6 kΩ or higher
    J28-22 (CANH) - J28-21 (CANL)*2
    Y - W
    Ignition switch OFF
    108 to 132 Ω
    J28-22 (CANH) - J28-40 (E1)*2
    Y - W-B
    Ignition switch OFF
    200 Ω or higher
    J28-21 (CANL) - J28-40 (E1)*2
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J28-22 (CANH) - J28-18 (B)*2
    Y - LG
    Ignition switch OFF
    6 kΩ or higher
    J28-21 (CANL) - J28-18 (B)*2
    W - LG
    Ignition switch OFF
    6 kΩ or higher

    HINT:
    1. *1: for V bus
    2. *2: for MS bus


CHECK STEERING ANGLE SENSOR

C159491E01

  1. Disconnect the J6 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J6-10 (CANH) - J6-9 (CANL)
    G - W
    Ignition switch OFF
    54 to 69 Ω
    J6-10 (CANH) - J6-2 (ESS)
    G - W-B
    Ignition switch OFF
    200 Ω or higher
    J6-9 (CANL) - J6-2 (ESS)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J6-10 (CANH) - J6-3 (BAT)
    G - R
    Ignition switch OFF
    6 kΩ or higher
    J6-9 (CANL) - J6-3 (BAT)
    W - R
    Ignition switch OFF
    6 kΩ or higher


CHECK 4WD CONTROL ECU

HINT:
For vehicle with 4 wheel drive only.


C159479E01

  1. Disconnect the A25 and A26 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    A25-19 (CANH) - A25-20 (CANL)
    BE - W
    Ignition switch OFF
    54 to 69 Ω
    A25-19 (CANH) - A26-4 (GND)
    BE - W-B
    Ignition switch OFF
    200 Ω or higher
    A25-20 (CANL) - A26-4 (GND)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    A25-19 (CANH) - J17-16 (BAT)
    BE - P
    Ignition switch OFF
    6 kΩ or higher
    A25-20 (CANL) - J17-16 (BAT)
    W - P
    Ignition switch OFF
    6 kΩ or higher


CHECK BUS BUFFER ECU
C159601E01

HINT:
For vehicle with bus buffer ECU only.

  1. Disconnect the J59 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J59-3 (CAN+) - J59-2 (CAN-)
    P - W
    Ignition switch OFF
    54 to 69 Ω


CHECK FRONT POWER SEAT CONTROL ECU AND SWITCH LH

HINT:
For vehicle with front power seat control system (w/ Seat memory) only.


C159480E01

  1. Disconnect the Z9 and Z10 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    Z10-5 (CANH) - Z10-1 (CANL)
    GR - W
    Ignition switch OFF
    54 to 69 Ω
    Z10-5 (CANH) - Z9-1 (GND)
    GR - W-B
    Ignition switch OFF
    200 Ω or higher
    Z10-1 (CANL) - Z9-1 (GND)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    Z10-5 (CANH) - Z9-5 (+B)
    GR - L
    Ignition switch OFF
    6 kΩ or higher
    Z10-1 (CANL) - Z9-5 (+B)
    W - L
    Ignition switch OFF
    6 kΩ or higher


CHECK OUTER MIRROR CONTROL ECU

HINT:
For vehicle with front power seat control system (w/ Seat memory) only.


C159485E01

  1. Disconnect the N7 and N8 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    N8-1 (CAN) - N8-21 (CGND)
    LG - W
    Ignition switch OFF
    54 to 69 Ω
    N8-11 (CAN) - N7-9 (GND)
    LG - W-B
    Ignition switch OFF
    200 Ω or higher
    N8-21 (CGND) - N7-9 (GND)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    N8-1 (CAN) - N7-3 (B)
    LG - R
    Ignition switch OFF
    6 kΩ or higher
    N8-21 (CGND) - N7-3 (B)
    W - R
    Ignition switch OFF
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU

HINT:
For vehicle with front power seat control system (w/ Seat memory) only.


C159486E01

  1. Disconnect the J47 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    J47-5 (CANH) - J47-14 (CANL)
    BE - W
    Ignition switch OFF
    54 to 69 Ω
    J47-5 (CANH) - J47-11 (GND)
    BE - W-B
    Ignition switch OFF
    200 Ω or higher
    J47-14 (CANL) - J47-11 (GND)
    W - W-B
    Ignition switch OFF
    200 Ω or higher
    J47-5 (CANH) - J47-2 (+B)
    BE - V
    Ignition switch OFF
    6 kΩ or higher
    J47-14 (CANL) - J47-2 (+B)
    W - V
    Ignition switch OFF
    6 kΩ or higher