Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.

  2. The table below shows the effects on each system when communication is impossible. For further details, refer to each system.

    Function (Function Description)
    Control Master ECU
    Related ECU or Sensor
    Vehicle Behavior
    Indicator and Buzzer
    Memory
    (Driver Seat, Mirror, Tilt and Telescopic)
    Front Power Seat Control ECU and Switch LH
    1. Outer Mirror Control ECU
    2. Multiplex Tilt and Telescopic ECU
    3. Main Body ECU
    4. ECM
    5. Combination Meter ECU
    Stop memory function
    Nothing
    Retractable Mirror
    Outer Mirror Control ECU
    Main Body ECU
    Stop Retractable function
    Nothing
    Door Mirror Foot Light
    Outer Mirror Control ECU
    Main Body ECU
    Stop door mirror foot light function
    Nothing
    Tilt and Telescopic: Auto Away/ Return
    Multiplex Tilt and Telescopic ECU
    1. Front Power Seat Control ECU and Switch LH
    2. Main Body ECU
    Stop auto away/ return function
    Nothing
    Alarm
    Main Body ECU
    Bus Buffer ECU
    Not influenced
    Nothing
    Door Lock Linked Speed
    Main Body ECU
    1. Combination Meter ECU
    2. Bus Buffer ECU
    Not possible to link with speed or shift
    Nothing
    Illumination
    Main Body ECU
    Combination Meter ECU
    Change status of illumination
    Nothing
    Cargo Light
    Main Body ECU
    Bus Buffer ECU
    Not influenced
    Nothing
    Power Window
    Main Body ECU
    Bus Buffer ECU
    Not influenced
    Nothing
    DRL
    Main Body ECU
    ECM
    DRL does not illuminate
    Nothing
    Observation Function of MS Bus Communication Failure
    Main Body ECU
    1. Front Power Seat Control ECU and Switch LH
    2. Outer Mirror Control ECU
    3. Multiplex Tilt and Telescopic ECU
    Not influenced
    Nothing
    Engine Control
    ECM
    -
    Not influenced
    Light on "MIL"*1
    Normal Brake
    Skid Control ECU with Actuator
    -
    Not influenced
    Nothing
    ABS, VSC
    Skid Control ECU with Actuator
    1. 4WD Control ECU
    2. ECM
    3. Steering Angle Sensor
    4. Yaw Rate Sensor
    1. Stop VSC operation
    2. Stop traction control
    1. Light on "VSC Warning Light"
    2. Light on "Slip Indicator Light"
    Meter Buzzer Function
    Combination Meter ECU
    1. Main Body ECU
    2. ECM
    3. Skid Control ECU with Actuator
    4. Center Airbag Sensor
    Stop some buzzer function
    1. Stop "Key Reminder Buzzer"
    2. Stop "Seat Belt Warning Buzzer"
    3. Stop "Parking Brake ON Drive Warning Buzzer"
    4. Stop "Half-open Warning Buzzer"
    5. Stop "4WD Buzzer"
    6. Stop "Slide Roof Buzzer"
    7. Stop "Sports Shift Reject Buzzer"
    Meter Indicator Function
    Combination Meter ECU
    1. Main Body ECU
    2. ECM
    3. Skid Control ECU
    4. Center Airbag Sensor
    5. 4WD Control ECU
    Does not illuminate or always illuminates
    1. Light on "Airbag Warning Light"
    2. Light on "BRAKE Warning Light"
    3. Light on "ABS Warning Light"
    Data Recorder
    Center Airbag Sensor
    1. ECM
    2. Combination Meter ECU
    Stop recording
    Light on "ABS Warning Light"
    A/C
    Air Conditioning Amplifier
    1. Main Body ECU
    2. ECM
    3. Combination Meter ECU
    Stop air conditioner
    Nothing
    Remote Start
    Bus Buffer ECU
    Main Body ECU
    Not possible to control by wireless
    Nothing
    4WD
    4WD Control ECU
    1. ECM
    2. Skid Control ECU with Actuator
    3. Combination Meter ECU
    4. Air Conditioning Amplifier
    Not possible to change between 4WD and 2WD
    Nothing

    NOTICE:
    *1: MIL lights on only during VSC or ABS failure status.