Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in CAN Main Wire

for Preparation Click here


DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 69 Ω or higher.
  1. CAN main wire and connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. ECM
  5. Combination Meter ECU

WIRING DIAGRAM


C158941E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.


NEXT


2.CHECK DLC3


    H102392E70
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    J17-6 (CANH) - J17-14 (CANL)
    Ignition switch OFF
    54 to 69 Ω
    OK
    69 Ω or higher
    NG

    NOTICE:
    When the measured value is 132 Ω or higher and a CAN communication system DTC is output, there may be a problem besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C159609E01
  1. Disconnect the J94 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J94-1 (CANH) - J94-2 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
Go to step 5
OK


4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E66
  1. Disconnect the J84 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J84-1 (CANH) - J84-2 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
Go to step 10
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

5.CONNECT CONNECTOR
  1. Reconnect the J94 No. 1 junction connector connector.


NEXT


6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C159609E03
  1. Disconnect the J92 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J92-1 (CANH) - J92-2 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
Go to step 8
OK


7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C159609E04
  1. Disconnect the J93 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J93-1 (CANH) - J93-2 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the J92 No. 2 junction connector connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 2 JUNCTION CONNECTOR)


    C159493E01
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-10 (CANH) - A24-11 (CANL)
    Ignition switch OFF
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 2UZ-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 3UR-FBE)
    D
    NG
    E



B
REPLACE ECM

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 JUNCTION CONNECTOR)
A

REPLACE ECM  

10.CONNECT CONNECTOR
  1. Reconnect the J84 No. 1 junction connector connector.


NEXT


11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR)


    C159487E08
  1. Disconnect the J28 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-33 (CANH) - J28-34 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY