Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

DTC    U1002    Lost Communication with Gateway Module

for Preparation Click here


DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open. (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open.)

DTC Code
Symptom
Trouble Area
U1002
Lost communication with gateway module
  1. MS bus circuit
  2. Front power seat control ECU and switch LH branch wire or connector
  3. Multiplex tilt and telescopic ECU branch wire or connector
  4. Outer mirror control ECU branch wire or connector
  5. Combination meter ECU main wire or connector
  6. Main body ECU main wire or connector
  7. Front power seat control ECU and switch LH
  8. Multiplex tilt and telescopic ECU
  9. Outer mirror control ECU
  10. Combination meter ECU
  11. Main body ECU
  12. No. 3 junction connector

WIRING DIAGRAM


C158944E01


INSPECTION PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.


NEXT


2.CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)


    C159606E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance of Malfunction
    J28-22 (CANH) - J28-21 (CANL)
    Ignition switch OFF
    54 to 69 Ω
    Below 53 Ω: Short in line
    70 Ω or higher: Open in CAN main bus line
    J28-22 (CANH) - J28-18 (B)
    Ignition switch OFF
    6 kΩ higher
    Below 6 kΩ: +B short
    J28-21 (CANL) - J28-18 (B)
    J28-22 (CANH) - J28-40 (E1)
    Ignition switch OFF
    200 Ω or higher
    Below 200 Ω: Ground short
    J28-21 (CANL) - J28-40 (E1)

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main wire
    A
    NG
    - Short in line
    - +B short
    - Ground short
    B
    OK
    C



B
Go to step 10

C
Go to step 29
A


3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C137766E63
  1. Disconnect the J97 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J97-1 (CANH) - J97-2 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
Go to step 8
OK


4.CONNECT CONNECTOR
  1. Reconnect the J97 No. 3 junction connector connector.


NEXT


5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E64
  1. Disconnect the J95 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J95-1 (CANH) - J95-2 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
Go to step 6
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

6.CONNECT CONNECTOR
  1. Reconnect the J95 No. 3 junction connector connector.


NEXT


7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)


    C159487E02
  1. Disconnect the J28 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-22 (CANH) - J28-21 (CANL)
    Ignition switch OFF
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY  

8.CONNECT CONNECTOR
  1. Reconnect the J97 No. 3 junction connector connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)


    C159597E01
  1. Disconnect the J2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J2-16 (CANP) - J2-15 (CANN)
    Ignition switch OFF
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT CONTROL ECU AND SWITCH LH)


    C159607E01
  1. Disconnect the J90 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J90-1 (CANH) - J90-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J90-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J90-2 (CANL) - J17-4 (CG)
    J90-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J90-2 (CANL) - J17-4 (CG)
    J90-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J90-2 (CANL) - J17-16 (BAT)
    J90-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J90-2 (CANL) - J17-16 (BAT)



NG
Go to step 19
OK


11.CONNECT CONNECTOR
  1. Reconnect the J90 No. 3 junction connector connector.


NEXT


12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)


    C159607E02
  1. Disconnect the J89 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J89-1 (CANH) - J89-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J89-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J89-2 (CANL) - J17-4 (CG)
    J89-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J89-2 (CANL) - J17-4 (CG)
    J89-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J89-2 (CANL) - J17-16 (BAT)
    J89-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J89-2 (CANL) - J17-16 (BAT)



NG
Go to step 21
OK


13.CONNECT CONNECTOR
  1. Reconnect the J89 No. 3 junction connector connector.


NEXT


14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)


    C159608E01
  1. Disconnect the J91 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J91-1 (CANH) - J91-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J91-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J91-2 (CANL) - J17-4 (CG)
    J91-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J91-2 (CANL) - J17-4 (CG)
    J91-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J91-2 (CANL) - J17-16 (BAT)
    J91-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J91-2 (CANL) - J17-16 (BAT)



NG
Go to step 23
OK


15.CONNECT CONNECTOR
  1. Reconnect the J91 No. 3 junction connector connector.


NEXT


16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C159607E03
  1. Disconnect the J95 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J95-1 (CANH) - J95-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J95-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J95-2 (CANL) - J17-4 (CG)
    J95-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J95-2 (CANL) - J17-4 (CG)
    J95-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J95-2 (CANL) - J17-16 (BAT)
    J95-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J95-2 (CANL) - J17-16 (BAT)



NG
Go to step 25
OK


17.CONNECT CONNECTOR
  1. Reconnect the J95 No. 3 junction connector connector.


NEXT


18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C159607E04
  1. Disconnect the J97 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J97-1 (CANH) - J97-2 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J97-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J97-2 (CANL) - J17-4 (CG)
    J97-1 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J97-2 (CANL) - J17-4 (CG)
    J97-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J97-2 (CANL) - J17-16 (BAT)
    J97-1 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J97-2 (CANL) - J17-16 (BAT)



NG
Go to step 27
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

19.CONNECT CONNECTOR
  1. Reconnect the J90 No. 3 junction connector connector.


NEXT


20.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT CONTROL ECU AND SWITCH LH)


    C159484E01
  1. Disconnect the Z10 front power seat control ECU and switch LH connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    Z10-5 (CANH) - Z10-1 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    Z10-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    Z10-1 (CANL) - J17-4 (CG)
    Z10-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    Z10-1 (CANL) - J17-4 (CG)
    Z10-5 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    Z10-1 (CANL) - J17-16 (BAT)
    Z10-5 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    Z10-1 (CANL) - J17-16 (BAT)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT POWER SEAT CONTROL ECU AND SWITCH LH (CANH, CANL)
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)  

21.CONNECT CONNECTOR
  1. Reconnect the J89 No. 3 junction connector connector.


NEXT


22.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)


    C159591E01
  1. Disconnect the J47 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J47-5 (CANH) - J47-14 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J47-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J47-14 (CANL) - J17-4 (CG)
    J47-5 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J47-14 (CANL) - J17-4 (CG)
    J47-5 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J47-14 (CANL) - J17-16 (BAT)
    J47-5 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J47-14 (CANL) - J17-16 (BAT)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANH, CANL)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU  

23.CONNECT CONNECTOR
  1. Reconnect the J91 No. 3 junction connector connector.


NEXT


24.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU)


    C158955E01
  1. Disconnect the N8 outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    N8-1 (CAN) - N8-21 (CGND)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    N8-1 (CAN) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    N8-21 (CGND) - J17-4 (CG)
    N8-1 (CAN) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    N8-21 (CGND) - J17-4 (CG)
    N8-1 (CAN) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    N8-21 (CGND) - J17-16 (BAT)
    N8-1 (CAN) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    N8-21 (CGND) - J17-16 (BAT)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU (CAN, CGND)
OK

REPLACE OUTER MIRROR CONTROL ECU  

25.CONNECT CONNECTOR
  1. Reconnect the J95 No. 3 junction connector connector.


NEXT


26.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C158955E02
  1. Disconnect the J28 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J28-22 (CANH) - J28-21 (CANL)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J28-22 (CANH) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J28-21 (CANL) - J17-4 (CG)
    J28-22 (CANH) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J28-21 (CANL) - J17-4 (CG)
    J28-22 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J28-21 (CANL) - J17-16 (BAT)
    J28-22 (CANH) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J28-21 (CANL) - J17-16 (BAT)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)
OK

REPLACE COMBINATION METER ASSEMBLY  

27.CONNECT CONNECTOR
  1. Reconnect the J97 No. 3 junction connector connector.


NEXT


28.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E01
  1. Disconnect the J2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    J2-16 (CANP) - J2-15 (CANN)
    Ignition switch OFF
    1 Ω or higher
    OK
    Below 1 Ω
    NG
    J2-16 (CANP) - J17-4 (CG)
    Ignition switch OFF
    1 Ω or higher
    OK
    J2-15 (CANN) - J17-4 (CG)
    J2-16 (CANP) - J17-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    J2-15 (CANN) - J17-4 (CG)
    J2-16 (CANP) - J17-16 (BAT)
    Ignition switch OFF
    1 Ω or higher
    OK
    J2-15 (CANN) - J17-16 (BAT)
    J2-16 (CANP) - J17-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    J2-15 (CANN) - J17-16 (BAT)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

29.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
  1. Reconnect the cable to the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

  1. Disconnect the DA, DB and DD main body ECU connectors.



  1. Measure the resistance according to the value(s) in the table below.


    E146246E03

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU