Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Body Electrical / (desired menu) / Data List.

  7. According to the display on the Techstream, read the "Data List".

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Room temperature sensor /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual room temperature for front seat is displayed
    Open in circuit: -6.5°C (20.3°F)
    Short in circuit: 57.25°C (135.05°F)
    Ambient Temp Sensor
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature is displayed
    Open in circuit: -23.3°C (-9.94°F)
    Short in circuit: 65.95°C (150.71°F)
    Evaporator Fin Thermistor
    Evaporator fin thermistor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    Open in circuit: -29.7°C (-21.46°F)
    Short in circuit: 59.55°C (139.19°F)
    Solar Sensor (D Side)
    Driver side solar sensor /
    Min.: 0, Max.: 255
    Driver side solar sensor voltage increases as brightness increases
    Open in circuit: 0
    Short in circuit: 255
    Solar Sensor (P Side)
    Passenger side solar sensor /
    Min.: 0, Max.: 255
    Passenger side solar sensor voltage increases as brightness increases
    Open in circuit: 0
    Short in circuit: 255
    Engine Coolant Temp
    Engine coolant temperature /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature is displayed while engine is warmed up
    -
    Set Temperature (D Side)
    Driver side set temperature /
    Min.: 0, Max.: 255
    Driver side actual set temperature is displayed
    -
    Set Temperature (P Side)
    Passenger side set temperature /
    Min.: 0, Max.: 255
    Passenger side actual set temperature is displayed
    -
    Blower Motor Speed Level
    Blower motor speed level /
    Min.: 0 level,
    Max.: 31 level
    Increases in range between 0 and 31 as blower motor speed increases
    -
    Adjusted Ambient Temperature
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    Adjusted ambient temperature is displayed
    -
    Air Mix Servo Targ Pulse (D)
    Driver side air mix servo motor target pulse / Min.: 5, Max.: 104
    MAX. COLD: 5 (pulse)
    MAX. HOT: 104 (pulse)
    -
    Air Mix Servo Targ Pulse (P)
    Passenger side air mix servo motor target pulse / Min.: 6, Max.: 105
    MAX. COLD: 105 (pulse)
    MAX. HOT: 6 (pulse)
    -
    Air Outlet Servo Pulse (D)
    Driver side air outlet servo motor target pulse / Min.: 9, Max.: 97
    FACE: 9 (pulse)
    B/L: 32 (pulse)
    FOOT: 56 (pulse)
    FOOT/DEF: 83 (pulse)
    DEF: 97 (pulse)
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse /
    Min.: 7, Max.: 28
    REC: 7
    FRS: 28
    -
    Cool Air Bypass Pulse
    Cool air bypass servo motor target pulse /
    Min.: 8, Max.: 50
    Open: 8 (pulse)
    Close: 50 (pulse)
    -
    Shift Set Temperature
    Shift set temperature / +2 C, +1 C, Normal, -1 C, -2 C
    Customized value will be displayed
    -
    Air Inlet Mode
    Air inlet mode / Auto, Manual
    Customized value will be displayed
    -
    Compressor Mode
    Compressor mode / Auto, Manual
    Customized value will be displayed
    -
    Compressor/DEF Mode
    Compressor/DEF mode / Link, Normal
    Customized value will be displayed
    -
    Foot/DEF Auto Mode
    FOOT/DEF auto mode / ON, OFF
    Customized value will be displayed
    -
    Foot/DEF Auto Blow Up
    FOOT/DEF auto blower up function / ON, OFF
    Customized value will be displayed
    -
    Ambient Temperature Shift
    Ambient temperature shift / +3 C, +2 C, +1 C, Normal, -1 C, -2 C, -3 C
    Customized value will be displayed
    -
    Destination
    Destination / DOMEST, USA, EUROPE, AUSTRAL, MIDEAST, NO INFO
    Changes value with destinations
    -
    Number of Trouble Codes
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs will be displayed
    -

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    Air conditioning switch signal /
    ON or OFF
    ON: Air conditioning ON
    OFF: Air conditioning OFF
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  5. According to the display on the Techstream, perform the "Active Test".

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower motor
    Min.: 0, Max.: 31
    -
    Magnetic Clutch Relay
    Magnetic clutch relay
    ON or OFF
    -
    Air Mix Servo Targ Pulse (D)
    Driver side air mix servo motor pulse
    Min.: 5, Max.: 104
    -
    Air Mix Servo Targ Pulse (P)
    Passenger side air mix servo motor pulse
    Min.: 6, Max.: 105
    -
    Air Outlet Servo Pulse (D)
    Driver side air outlet servo motor pulse
    Min.: 9, Max.: 97
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 7, Max.: 28
    -
    Cool Air Bypass Pulse
    Driver side cool air bypass pulse
    Min.: 8, Max.: 50
    -