AIR CONDITIONING UNIT > REASSEMBLY |
| 1. INSTALL COOLER EXPANSION VALVE |
![]() |
Sufficiently apply compressor oil to 4 new O-rings and the fitting surface of the hose joint.
Install the 2 O-rings to the cooler evaporator.
Install the 2 O-rings to the tube and accessory.
Install the cooler expansion valve and tube and accessory to the evaporator.
Using a 4 mm hexagon wrench, install the 2 bolts.
| 2. INSTALL EVAPORATOR TEMPERATURE SENSOR |
![]() |
Insert the sensor to a location that is 1 fin to the right or left of its previous location.
| Area | Standard Dimension |
| a | 48 mm (1.89 in.) |
| b | 9 mm (0.354 in.) |
| c | 34.3 mm (1.35 in.) |
| d | 47.7 mm (1.88 in.) |
| e | 50 mm (1.97 in.) |
| 3. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
![]() |
Install the evaporator to the blower case (front side).
![]() |
Install the blower case (back side).
Install the 6 screws and attach the 4 claws.
![]() |
Install the packing, as shown in the illustration.
| 4. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY |
![]() |
Install the heater radiator unit.
Attach the 3 claws to install the heater clamp.
![]() |
Install the plate with the 3 screws.
| 5. INSTALL COOLING UNIT DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Install the damper servo with the 3 screws, as shown in the illustration.
Connect the connector.
| 6. INSTALL BLOWER DAMPER SERVO SUB-ASSEMBLY |
![]() |
Install the damper servo with the 3 screws.
Connect the connector.
| 7. INSTALL BLOWER CASE SUB-ASSEMBLY |
![]() |
Attach the 3 claws to install the case.
Install the 3 screws.
| 8. INSTALL DAMPER SERVO SUB-ASSEMBLY |
![]() |
Install the damper servo with the 3 screws.
Connect the connector.
| 9. INSTALL DAMPER SERVO SUB-ASSEMBLY |
![]() |
Install the servo motor.
Set the plate so that the cutout part engages with the tooth of the gear, and attach the claw to install the main plate.
Install the 2 screws.
![]() |
Install the servo motor.
Insert the pin into the plate groove.
Attach the claw to install the main plate.
Install the 2 screws.
Set the damper servo so that the cutout part engages with the tooth of the gear, and attach the claw to install the damper servo.

![]() |
Install the 4 screws and connect the 2 connectors.
| 10. INSTALL AIR DUCT |
![]() |
Install the duct with the 2 screws.
| 11. INSTALL BLOWER WITH FAN MOTOR SUB-ASSEMBLY |
![]() |
Install the motor with the 3 screws.
| 12. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Install the amplifier with the 2 screws.
| 13. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY |
![]() |
install the duct with the screw.
| 14. INSTALL CLEAN AIR FILTER |
![]() |
Install the filter as shown in the illustration.
| 15. INSTALL AIR FILTER COVER PLATE |
![]() |
Attach the 2 clips to install the plate.
| 16. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY |
![]() |
Attach the 4 claws to install the duct.
| 17. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY |
![]() |
Attach the 4 claws to install the nozzle.