Home › ENGINE ยท 2UZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 AIR HOSE


    A191535
  1. Disconnect the air switching valve connector.

  1. Disconnect the fuel hose clamp.



    A153516
  1. Remove the air hose.



2. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 1)


A191536E01
  1. Remove the 3 nuts and air switching valve.

    NOTICE:
    Do not hold the bracket of the air switching valve.



3. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 2)


A153513E01
  1. Remove the 3 nuts and air switching valve.

    NOTICE:
    Do not hold the bracket of the air switching valve.



4. REMOVE IGNITION COIL ASSEMBLY


    A191542
  1. Disconnect the 8 ignition coil connectors.

  1. Remove the 8 bolts and pull out the 8 ignition coils.



5. REMOVE VACUUM HOSE ASSEMBLY


    A191537
  1. Remove the bolt and disconnect the vacuum hose assembly.



6. REMOVE NO. 2 WATER BY-PASS PIPE


    A191538
  1. Disconnect the 2 water hoses from the No. 2 water by-pass pipe.



    A191539
  1. Remove the 2 bolts.

  1. Remove No. 2 water by-pass pipe together with the water hose.



7. REMOVE INTAKE MANIFOLD


    A156170
  1. Disconnect the throttle position sensor and control motor connector.

  1. Disconnect the 2 water by-pass hoses from the throttle body.



    A191540E01
  1. Disconnect the No. 1 ventilation hose from the ventilation valve on the LH cylinder head.



    A156171
  1. Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.



    A163715
  1. Disconnect the VSV connector.



    A156174E02
  1. Disconnect the 2 wire clamps from the wire bracket and engine hanger.

  1. Remove the bolt and wire bracket from the intake manifold.



    A163553
  1. Disconnect the 2 wire clamps from the wire clamp bracket on the RH delivery pipe.

  1. Disconnect the 8 injector connectors.



    A156173
  1. Remove the 2 bolts and disconnect the engine wire protector.



    A156172
  1. Remove the 6 bolts, 4 nuts, intake manifold and 2 gaskets.



8. REMOVE AIR TUBE


    A153517
  1. Remove the 3 bolts, air tube and gasket.



9. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A160760E01
  1. Remove the bolt and pull out the water by-pass pipe.

  1. Remove the O-ring from the water by-pass pipe.



10. REMOVE NO. 4 AIR INJECTION SYSTEM HOSE


11. REMOVE AIR PUMP ASSEMBLY


A153506E01
  1. Disconnect the air pump connector.

  1. Remove the 2 bolts, 2 nuts and air pump.



12. REMOVE STARTER ASSEMBLY


    A159480
  1. Remove the 2 bolts holding the starter to the cylinder block.

  1. Disconnect the starter from the cylinder block.



    A159481
  1. Remove the bolt and disconnect the engine wire protector from the starter.

  1. Remove the bolt and ground wire.

  1. Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.

  1. Remove the starter.



13. REMOVE WATER INLET HOUSING


    A122973
  1. Disconnect the water by-pass hose from the water inlet housing.

  1. Remove the 2 bolts holding the water inlet housing to the water pump.

  1. Disconnect the water inlet housing from the front water by-pass joint, and remove the water inlet and inlet housing assembly.

  1. Remove the O-ring from the water inlet housing.



14. REMOVE FRONT WATER BY-PASS JOINT


    A115096
  1. Remove the 4 nuts, water by-pass joint and 2 gaskets.



15. REMOVE REAR WATER BY-PASS JOINT


    A160761
  1. Disconnect the air hose and remove the 4 nuts, water by-pass joint and 2 gaskets.



16. REMOVE OIL COOLER PIPE


    A108784E04
  1. Remove the cap nut and bolt.

  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to disconnect the 3 water by-pass hoses and remove the oil cooler pipe.



17. REMOVE NO. 2 WIRING HARNESS HEAT INSULATOR


    A160781
  1. Remove the 2 bolts and heat insulator.



18. REMOVE FRONT ENGINE MOUNTING INSULATOR RH


    A160787E01
  1. Remove the nut and mounting insulator.



19. REMOVE FRONT ENGINE MOUNTING INSULATOR LH


    A160788E01
  1. Remove the nut and mounting insulator.



20. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A160775
  1. Remove the 4 bolts and mounting bracket.



21. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    A160774
  1. Remove the 4 bolts and mounting bracket.



22. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)


    A153480
  1. Disconnect the oil control valve connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.



23. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)


    A191532
  1. Disconnect the connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.



24. REMOVE VVT SENSOR


    A159539
  1. Disconnect the 2 sensor connectors.

  1. Remove the 2 bolts and 2 sensors.



25. REMOVE KNOCK CONTROL SENSOR


    A159538
  1. Disconnect the 2 sensor connectors.

  1. Remove the 2 nuts and 2 sensors.



26. REMOVE CRANKSHAFT POSITION SENSOR


    A153483
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



27. REMOVE VENTILATION VALVE SUB-ASSEMBLY


A113204