Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Taillight Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a light control switch information signal from the headlight dimmer switch, and illuminates the taillights.

WIRING DIAGRAM


E146812E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (TAILLIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tail light
    Taillight
    ON or OFF
    -

    OK:
    Taillight turns on / turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (TAIL)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    TAIL fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (TAILLIGHT BULB - BATTERY)
E146275E01
E146275E02
  1. for LH:

    1. Disconnect the R5 taillight connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      R5-4 (TL) - Body ground
      Light control switch TAIL
      11 to 14 V
      Light control switch expect TAIL
      Below 1 V

  1. for RH:

    1. Disconnect the R4 taillight connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      R4-4 (TL) - Body ground
      Light control switch TAIL
      11 to 14 V
      Light control switch expect TAIL
      Below 1 V



NG
Go to step 4
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TAILLIGHT - BODY GROUND) 

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
E147142E01
  1. Disconnect the DA ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (TAILLIGHT - MAIN BODY ECU)

E147143E01

  1. Disconnect the DB ECU connector.

  1. for LH:

    1. Disconnect the R5 taillight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      R5-4 (TL) - DB-8
      Always
      Below 1 Ω
      R5-4 (TL) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the R4 taillight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      R4-4 (TL) - DB-8
      Always
      Below 1 Ω
      R4-4 (TL) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU