Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Cargo Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a cargo light information signal from the cargo light switch and door courtesy light switch, and illuminates the cargo light.

WIRING DIAGRAM


E147662E02


INSPECTION PROCEDURE

1.INSPECT FUSE (CARGO)
  1. Remove the CARGO fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    CARGO fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (CARGO LIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Cargo Lgt
    Cargo light
    ON or OFF
    Cargo light switch is DOOR or ON

    OK:
    Cargo light turns on / off.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.READ VALUE USING TECHSTREAM (CARGO LIGHT SWITCH)
  1. Operate the Techstream according to the display and select the "Data List".

    Main Body ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Cargo Light
    Cargo light switch signal / ON or OFF
    ON: Cargo light switch ON
    OFF: Cargo light switch OFF
    -

    OK:
    When cargo light switch operation is performed, the results are the same as above.



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (CARGO LIGHT - BATTERY AND BODY GROUND)
E146140E02
  1. Disconnect the P8 light connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P8-3 (DL) - Body ground
    Cargo light switch ON
    11 to 14 V
    Cargo light switch DOOR, door is open
    Cargo light switch OFF
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    P8-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.INSPECT CARGO LIGHT SWITCH
E143954E01
  1. Remove the cargo light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (FCTY) - 9 (FLON)
    Cargo light switch ON
    Below 1 Ω
    Cargo light switch DOOR
    Cargo light switch OFF
    10 kΩ or higher
    10 (FLMP) - 7 (E)
    Cargo light switch ON
    Below 1 Ω
    Cargo light switch DOOR
    10 kΩ or higher
    Cargo light switch OFF



NG
REPLACE CARGO LIGHT SWITCH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
E177839E01
  1. Disconnect the J3 and J4 ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J2-14 (CGLP) - Body ground
    Cargo light switch ON or DOOR
    11 to 14 V
    Cargo light switch OFF
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J3-9 (CGSW) - Body ground
    Cargo light switch ON
    Below 1 Ω
    Cargo light switch DOOR or OFF
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU