FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY |
| 1. REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type) |
![]() |
Using a screwdriver, detach the 2 claws and remove the vertical adjuster handle cap.
![]() |
Remove the 2 screws and vertical adjuster handle.
| 2. REMOVE VERTICAL SEAT ADJUSTER KNOB LH (for 8 Way Seat Type) |
![]() |
Remove the snap ring and vertical seat adjuster knob.
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Lift the reclining adjuster release handle.
Using a screwdriver, detach the claw and remove the reclining adjuster release handle.
| 4. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the hog rings and rubber bands of the seatback cover from the seat frame.
![]() |
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.
w/ Lumbar Support Adjuster:
Disconnect the switch connector.
| 5. REMOVE FRONT POWER SEAT LUMBAR SWITCH (w/ Lumbar Support Adjuster) |
Remove the 2 screws and switch.
| 6. REMOVE INNER FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the screw.
Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.
| 7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
Driver Side:
Disconnect the 2 connectors and detach the 4 clamps.
Passenger Side:
Disconnect the connector and detach the clamp.
![]() |
Remove the nut and front seat inner belt.
| 8. REMOVE FRONT SEAT CUSHION COVER WITH PAD LH |
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Remove the hog rings.
Bend the 2 seat frame claws upward.
Detach the hooks and remove the seat cushion cover with pad.
| 9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER LH |
![]() |
Remove the hog rings and seat cushion cover.
| 10. REMOVE FRONT SEAT HEADREST ASSEMBLY LH |
| 11. REMOVE FRONT SEATBACK COVER WITH PAD LH |
![]() |
Detach the hook.
![]() |
Remove the hog rings and seatback cover wires.
![]() |
Remove the nut and seatback cover bracket from the seat frame.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
![]() |
Remove the hog rings and seatback cover with pad.
| 12. REMOVE SEPARATE TYPE FRONT SEATBACK COVER LH |
![]() |
Remove the hog rings and seatback cover wires.
![]() |
Disconnect the seatback cover bracket from the seatback pad.
![]() |
Remove the hog rings and seatback cover from the seatback pad.
| 13. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw and reclining adjuster inside cover.
| 14. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
Remove the screw and reclining adjuster inside cover.
| 15. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Detach the claw and remove the reclining adjuster inside cover.
| 16. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
Remove the screw.
Detach the claw and remove the reclining adjuster inside cover.
| 17. REMOVE LOWER FRONT SEAT CUSHION SHIELD LH |
![]() |
Using a screwdriver, detach the claw and remove the seat cushion shield lower.
| 18. REMOVE LOWER FRONT SEAT CUSHION SHIELD RH |
Using a screwdriver, detach the claw and remove the seat cushion shield lower.
| 19. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support Adjuster) |
![]() |
Remove the 2 springs.
Detach the 6 hooks and remove the seatback spring.
![]() |
Disconnect the lumbar support adjuster connector.
Remove the 2 screws and lumbar support adjuster.
![]() |
Detach the 3 claws and remove the bush from the seat frame.
| 20. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the 2 ECU connectors.
Using a screwdriver, detach the claw and remove the ECU.
| 21. REMOVE SEAT POSITION AIRBAG SENSOR |
![]() |
Using a T30 "TORX" socket wrench, remove the screw and seat position sensor with sensor protector.
Disconnect the connector.
Remove the seat slide position sensor protector from the seat position sensor.
| 22. REMOVE FRONT SEAT WIRE LH |