Home › BODY › SEAT › REAR SEAT ASSEMBLY (for Double Cab)

REAR SEAT ASSEMBLY (for Double Cab) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat cushion frame and the seatback frame may injure your hands.



1. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH


B166540E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



2. INSTALL REAR SEATBACK COVER WITH PAD RH


B165780E02
  1. Install the seatback cover with pad to the rear seatback frame, and then attach the hooks.



3. INSTALL REAR SEAT HEADREST SUPPORT RH


B165779
  1. Attach 4 claws to install the 2 headrest supports.



4. INSTALL REAR SEAT HEADREST ASSEMBLY RH


5. INSTALL REAR SEAT TURN LOCK SUB-ASSEMBLY RH


B166339
  1. Install the seat turn lock with the bolt.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



6. INSTALL REAR SEAT HINGE COVER RH


B165767
  1. Install the hinge cover with the 2 screws.



7. INSTALL REAR SEAT HINGE COVER LH
  1. Install the hinge cover with the 2 screws.



8. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH


B165778E02
  1. Install the release handle with the 4 screws.

  1. Connect the cable and install a new cable tie.



9. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH


B166541E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



10. INSTALL REAR SEAT CUSHION COVER WITH PAD RH


B165776E02
  1. Using hog ring pliers, install the seat cushion cover with pad to the rear seat cushion frame with new hog rings, and then attach the hooks.



    B165775E02
  1. Attach the hooks to the seat cushion frame.



    B165774E02
  1. Fold down the seat cushion cover and close the 2 fasteners, and then attach the hook.



    B166342
  1. Connect the cable to the seat turn lock.



11. INSTALL REAR SEATBACK LOCK CONTROL BEZEL RH


B166337
  1. Attach the 4 claws to install the bezel.



12. INSTALL REAR SEAT CUSHION ASSEMBLY RH


B165773
  1. Using a T40 "TORX" socket, install the seat cushion with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



13. INSTALL OUTER REAR SEAT LOCK COVER RH


B166340E02
  1. Attach the clip and 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the screw.



14. INSTALL INNER REAR SEAT LOCK COVER RH


B166341E01
  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the 2 screws.



15. INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY


B166554
  1. Install the seat leg with the bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Using a T45 "TORX" socket, install the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



16. INSTALL SEAT LEG SUB ASSEMBLY LH


B166346
  1. Install the seat leg with the bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



17. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH


B166542E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



18. INSTALL REAR SEATBACK COVER WITH PAD LH


B165770E02
  1. Install the seatback cover with pad to the rear seatback frame, and then attach the hooks.



19. INSTALL REAR SEAT HEADREST SUPPORT


B165769
  1. Attach the 8 claws to install the 4 headrest supports.



20. INSTALL CENTER REAR SEAT HEADREST ASSEMBLY


21. INSTALL REAR SEAT HEADREST ASSEMBLY LH


22. INSTALL REAR SEAT TURN LOCK SUB-ASSEMBLY LH


B165768
  1. Install the seat turn lock with the bolt.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



23. INSTALL REAR SEAT HINGE COVER RH


B165767
  1. Install the hinge cover with the 2 screws.



24. INSTALL REAR SEAT HINGE COVER LH
  1. Install the hinge cover with the 2 screws.



25. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH


B165764E02
  1. Install the release handle with the 4 screws.

  1. Connect the cable and install a new cable tie.



26. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH


B166543E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



27. INSTALL REAR SEAT CUSHION COVER WITH PAD LH


B165613E02
  1. Using hog ring pliers, install the seat cushion cover with pad to the seat cushion frame with new hog rings.



    B165612E02
  1. Attach the hooks to the seat cushion frame.



    B165611E02
  1. Attach the hooks to the seat cushion frame.



    B165609E02
  1. Fold down the seat cushion cover and close the 2 fasteners, and then attach the hook.



    B166345
  1. Connect the cable to the rear seat turn lock.



28. INSTALL REAR SEATBACK LOCK CONTROL BEZEL LH


B165608
  1. Attach the 4 claws to install the bezel.



29. INSTALL REAR SEAT CUSHION ASSEMBLY LH


B165607
  1. Using a T40 "TORX" socket, install the seat cushion with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



30. INSTALL INNER REAR SEAT LOCK COVER LH


B166344E01
  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the 2 screws.



31. INSTALL OUTER REAR SEAT LOCK COVER LH


B166343E02
  1. Attach the 3 claws and clip in the order shown in the illustration, and install the cushion shield.

  1. Install the screw.



32. INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY RH


B165604
  1. Install the seat leg with the bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



33. INSTALL NO. 1 SEAT LEG SUB ASSEMBLY LH


B165603
  1. Install the seat leg with the bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Using a T45 "TORX" socket, install the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



34. INSTALL REAR SEAT ASSEMBLY LH


B165602
  1. Using a T50 "TORX" socket, install the seat with the 2 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }