Home › BODY › SEAT › FRONT SEATBACK HEATER (w/ Seat Heater System)

FRONT SEATBACK HEATER (w/ Seat Heater System) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH



B167120E01

  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with the tack pins.



2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER LH


B167191E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B166411
  1. Connect the seatback cover bracket to the seatback pad.



    B167104E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install new hog rings to the seatback pad.



3. INSTALL FRONT SEATBACK COVER WITH PAD LH
  1. Install the seatback cover with pad to the seatback frame.



    B165534E07
  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165529
  1. Attach the 4 claws to install the 2 headrest supports.



    B165533
  1. Install the seatback cover bracket to the seat frame with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

  1. Install the seatback cover wires.



    B167102E05
  1. Using hog ring pliers, install new hog rings to the seat frame.



    B167101E06
  1. Attach the hook.



    B167194
  1. Attach the wire harness clamp.

  1. Connect the seat heater connector.



4. INSTALL INNER FRONT SEAT CUSHION SHIELD LH


B166948
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



5. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


B166599E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.

  1. Driver Side:

    1. Connect the 2 connectors and attach the 4 clamps.

  1. Passenger Side:
    Connect the connector and attach the clamp.



6. INSTALL FRONT SEAT CUSHION SHIELD LH


B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B166944E02
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



7. INSTALL RECLINING POWER SEAT SWITCH KNOB LH


B167192
  1. Attach the 2 claws to install the knob.



8. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH


B167193
  1. Attach the 2 claws to install the knob.



9. INSTALL FRONT SEAT ASSEMBLY LH
  1. Install the front seat (Click here).