Home › BODY › MIRROR › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the tester on.

  4. Enter the following menus:

    1. Techstream - Select: Body / (desired system) / Data List.

  5. According to the display on, read the "DATA LIST".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror selection SW (R)
    Mirror master switch signal for RH mirror / ON or OFF
    ON: Switch is in R position
    OFF: Switch is OFF or in L position
    -
    Mirror selection SW (L)
    Mirror master switch signal for LH mirror / ON or OFF
    ON: Switch is in L position
    OFF: Switch is OFF or in R position
    -
    Mirror position SW (R)
    Mirror control switch signal (RIGHT) / ON or OFF
    ON: RIGHT switch is ON
    OFF: Any switch except RIGHT is ON or all switches are OFF
    -
    Mirror position SW (L)
    Mirror control switch signal (LEFT) / ON or OFF
    ON: LEFT switch is ON
    OFF: Any switch except LEFT is ON or all switches are OFF
    -
    Mirror position SW (UP)
    Mirror control switch signal (UP) / ON or OFF
    ON: UP switch is ON
    OFF: Any switch except UP is ON or all switches are OFF
    -
    Mirror position SW (Dwn)
    Mirror control switch signal (DOWN) / ON or OFF
    ON: DOWN switch is ON
    OFF: Any switch except DOWN is ON or all switches are OFF
    -
    Outer mirror fold SW
    Mirror retract switch signal / ON or OFF
    ON: Switch is ON (retracting)
    OFF: Switch is OFF
    -

    Mirror 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Memory No.1
    Driver side mirror position memorized in seat memory switch M1 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No.2
    Driver side mirror position memorized in seat memory switch M2 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    RH Mir Position Sensor V
    Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 255
    Within range from 0 to 255
    -
    RH Mir Position Sensor H
    Passenger side mirror vertical sensor voltage / MIN: 0, MAX: 255
    Within range from 0 to 255
    -
    LH Mir Position Sensor V
    Driver side mirror vertical sensor voltage / MIN: 0, MAX: 255
    Within range from 0 to 255
    -
    LH Mir Position Sensor H
    Driver side mirror vertical sensor voltage / MIN: 0, MAX: 255
    Within range from 0 to 255
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch OFF.

  3. Connect the the Techstream to the DLC3.

  4. Turn the ignition switch ON (IG).

  5. Turn the on.

  6. Enter the following menus:

    1. Techstream - Select: Body Electrical / MIRROR / Active Test.

  7. According to the display on tester, perform the "ACTIVE TEST".

  8. Techstream

    Mirror 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    RH Mirror Up/Down
    Mirror vertical operation
    UP / OFF / DOWN
    -
    RH Mirror Right/Left
    Mirror horizontal operation
    RIGHT / OFF / LEFT
    -
    LH Mirror Up/Down
    Mirror vertical operation
    UP / OFF / DOWN
    -
    LH Mirror Right/Left
    Mirror horizontal operation
    RIGHT / OFF / LEFT
    -
    Mirror Fold
    Mirror retract operation
    FOLD / OFF
    -
    Mirror Return
    Mirror retract operation
    RETURN / OFF
    -