Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



METER GAUGE AND WARNING/INDICATOR

Meter/Gauge: 
Item
Details
Speedometer
Based on signal received from wheel speed sensor, skid control ECU calculates vehicle speed and transmits data to combination meter (CAN)
Tachometer*1
Combination meter receives engine rpm signal from ECM, and gauge needle operates (CAN)
ODO/TRIP meter
  1. Combination meter receives vehicle speed pulse integration signal from skid control ECU, and ODO/TRIP meter display operates (CAN)
  2. Using ODO/TRIP switch, ODO/TRIP meter display changes
Fuel receiver gauge
Combination meter receives fuel amount information measured by fuel sender gauge, and gauge needle operates (Direct line)
Engine coolant temperature gauge*2
Combination meter receives water temperature signal from ECM, and gauge needle operates (CAN)
A/T oil pressure receiver gauge
Combination meter receives A/T oil temperature signal from ECM, and gauge needle operates (CAN)
Oil pressure receiver gauge*3
Combination meter receives engine rpm signal from ECM (CAN), and receives oil pressure sender signal from oil pressure sender (Direct line). Then meter measures signals and gauge needle operates.
Voltmeter*4
Monitors IG voltage and gauge needle operates (Direct line)

HINT:
*1: w/ Tachometer
*2: w/ Engine Coolant Temperature Gauge
*3: w/ Oil Pressure Receiver Gauge
*4: w/ Voltmeter


Warning/Indicator: 
Item
Details
BEAM indicator light
E146782
Receives signal from main body ECU (CAN)
A/T OIL TEMP warning light
E146783
Warning is displayed when oil temperature is high (CAN)
SRS warning light
E146784
Receives malfunction signal from center airbag sensor (CAN)
DOOR indicator light
E146785
Open door indicator comes on when signal is received from main body ECU (CAN)
Driver side seat belt warning light
E146786
Receives driver seat belt signal (Unfastened) from main body ECU (CAN)
Brake warning light*2
E146787
  1. Comes on when parking brake switch is ON (CAN)
  2. Brake fluid level warning switch is ON (Direct line)
  3. Vehicle stability control system is malfunctioning
Brake warning light*3
E146788
CHARGE warning light
E146789
Receives malfunction signal from generator (Direct line)
4LO indicator light*1
E146790
Receives 4LO signal from 4WD control ECU (CAN)
ABS warning light*2
E146791
Receives malfunction signal from skid control ECU (CAN)
ABS warning light*3
E146792
MIL
E146793
Receives malfunction signal from ECM (Direct line)
FUEL warning light
E146794
Receives fuel empty signal from fuel sender gauge (Direct line)
SLIP indicator light
E146795
Receives malfunction signal from skid control ECU (CAN)
4HI indicator light*1
E146796
Receives 4HI signal from 4WD control ECU (CAN)
CRUISE main indicator light
E146797
Receives CRUISE on signal or malfunction signal from ECM (CAN)
HEAD indicator light*2
E146798
Receives taillight or headlight signal from main body ECU (CAN)
TAIL indicator light*3
E146799
Receives taillight or headlight signal from main body ECU (CAN)
Turn signal indicator light (LH/RH)
E146800
Receives turn signal from FLASHER relay (Direct line)
AUTO LSD indicator light
E146801
Receives VSC OFF switch ON signal from skid control ECU (CAN)
VSC OFF indicator light
E146802
Receives VSC control off signal or VSC system fail-safe control signal from skid control ECU (CAN)
RSCA OFF indicator light*4
E146803
Receives RSCA OFF signal from center airbag sensor (Direct line)
TOW HAUL indicator light
E146804
Receives towing indicator signal from main body ECU (CAN)
Tire pressure warning light
E146805
Receives low tire pressure signal from tire pressure warning ECU (Direct line)
Master warning light*5
E146806
Receives warning signal from each ECU (CAN)
A/T P shift position indicator
Receives P signal from ECM (Direct line)
A/T N shift position indicator
Receives N signal from ECM (Direct line)
A/T D shift position indicator
Receives D signal from ECM (Direct line)
A/T 6 shift position indicator*6
Receives 6 signal from ECM (Direct line)
A/T 5 shift position indicator
Receives 5 signal from ECM (CAN)
A/T 4 shift position indicator
Receives 4 signal from ECM (CAN)
A/T 3 shift position indicator
Receives 3 signal from ECM (CAN)
A/T 2 shift position indicator
Receives 2 signal from ECM (CAN)
A/T 1 shift position indicator
Receives 1 signal from ECM (CAN)
A/T S shift position indicator
Receives S signal from ECM (Direct line)
A/T R shift position indicator
Receives R signal from ECM (Direct line)

HINT:
*1: for 4WD
*2: for U.S.A.
*3: except U.S.A.
*4: w/ Curtain Shield Airbag
*5: w/ Multi-information Display
*6: for 3UR-FE, 3UR-FBE


MULTI-INFORMATION DISPLAY (w/ Multi-information display)
When the INFO switch is pressed, the multi-information display is changed between the following: cruise information display, warning display.


  1. Cruise information display:
    The cruise information is displayed in the following order each time the INFO switch is pressed.


    E146751


    Display
    Outline
    Average Fuel Economy
    1. Value that has been calculated by combination meter, which is based on distance driven and fuel consumption volume (fuel injection signal from No. 1 cylinder)
    2. This display is updated every 10 seconds
    Current Fuel Economy
    1. Value that has been calculated by combination meter. When ignition switch is turned ON, combination meter calculates this value based on distance driven and fuel consumption volume (fuel injection signal from No. 1 injector).
    2. This display is updated every 0.5 seconds
    Distance To Empty
    1. Value that has been calculated by combination meter. When ignition switch is turned ON, combination meter calculates this value based on fuel consumption data that combination meter continuously monitors and stores in its memory, and residual fuel volume data.
    2. This display is updated every km (mile)
    Trip Timer
    1. Calculates and displays elapsed time since engine start signal was input into combination meter
    2. This display is updated every second
    Average Speed
    1. Value that has been calculated by combination meter. This calculation is based on elapsed time since engine start signal was received by combination meter and vehicle speed signal received by combination meter.
    2. This display is updated every 10 seconds



  2. Warning display:
    When a warning is necessary, the warning display interrupts the multi-information display.

    1. The master warning light may illuminate or blink and buzzer may sound depending on the item in the multi-information display.

    E146707E01


    Display
    Details
    1. DRIVER DOOR OPEN
    2. PASSENGER DOOR OPEN
    3. LEFT REAR DOOR OPEN
    4. RIGHT REAR DOOR OPEN
    Any door is open
    ENGINE COOLANT HOT
    Engine coolant temperature is more than 120°C (248°F)
    MAINT REQD SOON
    Comes on approximately 7242 km (4500 miles) after engine oil is changed
    PARKING BRAKE ENGAGED
    Parking brake is still engaged with vehicle having reached speed of 5 km/h (3 mph)
    LOW WASHER FLUID
    Washer fluid level is low
    LOW FUEL LEVEL
    Fuel level is low
    TRANSMISSION HOT
    ATF temperature is high
    MAINT REQD
    Comes on approximately 8047 km (5000 miles) after engine oil is changed


ACCESSORY METER
  1. This system has the following functions.

    1. Clock:
      When the ignition switch is turned ON or ACC, the clock display is ON.

    2. Cruise Information:
      For cruise information, four type of information (Outside temperature, average fuel economy, instant fuel economy, and distance to empty) can be displayed.

      1. The cruise information units can be changed by using the SETUP switch.
      1. Outside temperature → Average fuel economy → Instant fuel economy → Distance to empty.

        Information
        Outline
        Outside Temperature:
        B166704
        Displays outside temperature in accordance with the outside temperature sensor signal from the A/C amplifier (manual A/C) or A/C ECU (auto A/C).
        Average Fuel Economy:
        B166921
        1. Displays a value that has been calculated by the combination meter, which is based on the distance driven and the fuel consumption volume (fuel injection signal from the No. 1 cylinder).
        2. This display is updated every 0.5 seconds.
        Instant Fuel Economy:
        B166922
        1. Displays a value that has been calculated by the combination meter. When the ignition switch is turned ON, the combination meter calculates this value based on the distance driven and the fuel consumption volume (fuel injection signal from the No. 1 injector).
        2. This display is updated every 0.5 seconds.
        Distance to Empty:
        B168108
        1. When the ignition switch is ON, displays a value that has been calculated by the combination meter (meter ECU), which is based on the following: 1) fuel consumption data that the combination meter (meter ECU) continuously monitors and stores in its memory; and 2) residual fuel volume data.
        2. This display is updated every 1 mile (1.6 km).

    3. Security Indicator Light:

      1. informs the driver of the theft deterrent system status.
      2. Depending on operation of the transponder key ECU, the interior security indicator light comes on or starts blinking.

    4. Clearance Warning Indicator:

      1. Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.
      2. Turns on and off according to the intuitive parking assist system status.
      3. Emits an intermittent sound to inform the driver that the ECU has detected an obstacle within the prescribed ranges.