Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Glass Breakage Sensor ECU Circuit


DESCRIPTION

When the glass breakage sensor detects the glass is broken (1st time), the sensor will set off an alarm for 20 seconds (pre-alarm). If the glass breakage sensor detects that more glass is broken (2nd time or more), the sensor will set off an alarm for 60 seconds.

WIRING DIAGRAM


B165949E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (GLASS BREAKAGE SENSOR)
  1. Using the Techstream, read the Data List.

    MAIN BODY 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Glass Break Sensor Detection
    Glass breakage sensor detection /
    ON or OFF
    ON: Glass breakage sensor ON
    OFF: Glass breakage sensor OFF
    -

    OK:
    When tapping on the door glass with your finger, "ON" is displayed on the Techstream screen.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (ECU-IG No. 1)
  1. Remove the ECU-IG No. 1 fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - BATTERY AND BODY GROUND)


    B165953E01
  1. Disconnect the J57 glass breakage sensor ECU connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J57-2 (GB+B) - J57-6 (GND)
    Always
    11 to 14 V
    J57-3 (GBIG) - J57-6 (GND)
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J57-6 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - GLASS BREAKAGE SENSOR ECU)


    B165954E01
  1. Disconnect the J4 main body ECU connector.

  1. Disconnect the J57 glass breakage sensor ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J4-17 (GBS) - J57-5 (GBS1)
    Always
    Below 1 Ω
    J4-17 (GBS) or J57-5 (GBS1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - GLASS BREAKAGE SENSOR MICROPHONE)


    B165955E01
  1. Disconnect the J57 glass breakage sensor ECU connector.

  1. Disconnect the J58 glass breakage sensor microphone connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J57-8 (MI+) - J58-3 (MIC+)
    Always
    Below 1 Ω
    J57-7 (MI-) - J58-4 (MIC-)
    J57-8 (MI+) or J58-3 (MIC+)- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK GLASS BREAKAGE SENSOR ECU (GLASS BREAKAGE SENSOR OUTPUT)


    B165952E01
  1. Reconnect the J57 glass breakage sensor ECU connector.

  1. Reconnect the J58 glass breakage sensor microphone connector.

  1. Reconnect the J4 main body ECU connector.

  1. Turn the ignition switch ON.

  1. Using an oscilloscope, check the waveform.

    Standard:
    Test Connector
    Tool Setting
    Vehicle Condition
    Specified Condition
    J57-5 (GBS1) - Body ground
    1 V/DIV., 50 msec./DIV.
    Ignition switch ON
    Tap the door glass with a hard object such as your fingernail
    Pulse generation

    Result 
    Result
    Proceed to
    OK
    A
    NG
    (for Column Shift Type)
    B
    NG
    (for Floor Shift Type)
    C



B
REPLACE GLASS BREAKAGE SENSOR MICROPHONE (Click here)

C
REPLACE GLASS BREAKAGE SENSOR MICROPHONE (Click here)
A

REPLACE GLASS BREAKAGE SENSOR ECU (Click here)